MSDS Dry Shine Wash and Wax

00000485 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Item Numbers……………………………. A6-000008

Product Identity……………………………………… Dry Shine – 487g

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CHEM TREC: 800-424-9300.

Recommended Use………………………………… Waterless wash and wax.

Chemical Family…………………………………….. Mixture.

Section 02: HAZARDS IDENTIFICATION

Hazard Classification:

Physical Hazards……………………………………. Gases Under Pressure – Compressed gas. Flammable Aerosols – Category 1.

Health Hazards………………………………………. Not Classified.

Environmental Hazards…………………………… Not Classified.

Label Elements:

Signal Word…………………………………………… DANGER.

Hazard Statement………………………………….. Extremely flammable aerosol. Pressurized container: may burst if heated.

Precautionary Statements:

Prevention…………………………………………….. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No

smoking. Do not spray on an open flame or other ignition source. Do not pierce or burn,

even after use.

Response……………………………………………… Not applicable.

Storage…………………………………………………. Protect from sunlight. Do not expose to temperatures exceeding 50°C /122°F. Store in a

well ventilated place .

Disposal………………………………………………… Not applicable.

Hazard(s) not otherwise classified (HNOC).. None Known.

Section 03: COMPOSITION/INFORMATION ON INGREDIENTS

Hazardous Ingredients CAS # Wt. %

Isobutane 75-28-5 10-30

Hydrotreated Light Petroleum Distillate 64742-47-8 5-10

Propane 74-98-6 1-5

Section 04: FIRST AID MEASURES

Inhalation………………………………………………. If inhaled, remove to fresh air. If not breathing, give artificial respiration and obtain

immediate medical assistance.

Skin Contact………………………………………….. Wash exposed area with soap and water. Remove contaminated clothing. If irritation or

redness develops, seek medical attention.

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Ingestion……………………………………………….. Ingestion is not a likely route of exposure. If ingested, do not induce vomiting, get medical

attention.

Most important symptoms/effects, acute and Immediate medical attention is required.

delayed

Indication of immediate medical attention and Provide general supportive measures and treat symptomatically. In case of shortness of

special treatment needed breath give oxygen. Keep victim warm. Keep victim under observation. Symptoms may be

delayed.

00000485 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 05: FIRE FIGHTING MEASURES

Suitable Extinguishing Media…………………… Dry chemical powder. Carbon dioxide. Foam, water spray or fog.

Unsuitable Extinguishing Media……………….. Do not use water jet as an extinguisher, as this will spread the fire.

Specific Hazards Arising from the Chemical. Contents under pressure. Pressurized container may explode when exposed to heat or

flame.

Special Protective Equipment and …………… Firefighters must use standard protective equipment including flame retardant coat, helmet

Precautions for Firefighters with water to prevent vapor pressure build up. For massive fire in cargo area, use

unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.

General Fire Hazards……………………………… Flammable Aerosol.

Section 06: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment No action shall be taken involving any personal risk or without suitable training. Evacuate

and Emergency Procedures surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not

touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate

ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate

personal protective equipment (see Section 08).

Methods and Materials for Containment and Spill areas may be slippery. Use care to avoid falls or other accidents . Contain the spill.

Cleaning Up Clean up the spill area with detergent and water. Once spilled material has been collected,

use rags or other suitable material to clean spill area. Rags should be properly disposed of.

Environmental Precautions……………………… Keep out of drains, sewers, ditches, and waterways. Minimize use of water to prevent

environmental contamination.

Section 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is

missing or defective. Do not spray on a naked flame or any other incandescent material.

Do not pressurize, cut, weld, braze, solder, drill, grind, or expose empty containers to heat,

sparks or open flames. Avoid contact with eyes, skin, and clothing. Avoid breathing vapour

of this product. Avoid contact with skin and eyes. Avoid prolonged exposure. Use in

well-ventilated areas.

Conditions for Safe Storage including any … Store locked up. Pressurized container. Protect from sunlight and do not expose to

Incompatibilities temperatures exceeding 50°C (122°F). Do not puncture, incinerate or crush. Do not handle

or store near an open flame, heat or other sources of ignition. Store away from

incompatible materials (see Section 10).

Section 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

Ingredients TWA STEL PEL STEL REL

Isobutane 800 ppm 1000 ppm 800 ppm Not available 800 ppm (TWA)

Hydrotreated Light Not available Not available Not available Not available Not available

Petroleum Distillate

Propane 2,500 ppm Not available 1,000 ppm Not available 1,000 ppm

Appropriate Engineering Controls…………….. Local exhaust ventilation required to maintain the point of use below the Threshold Limit

Value if unprotected personnel are involved.

Individual Protection Measures:

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Chemical resistant gloves are recommended. Avoid contact with the skin. Wear

appropriate chemical resistant clothing.

Respiratory Protection…………………………….. Use dust and mist respirator.

Thermal Hazards……………………………………. None Known.

General Hygiene Considerations……………… When using, do not eat, drink or smoke. Always observe good personal hygiene measures,

such as washing after handling the material and before eating, drinking, and/or smoking.

Routinely wash work clothing and protective equipment to remove contaminants.

Section 09: PHYSICAL AND CHEMICAL PROPERTIES

Form…………………………………………………….. Aerosol.

Physical Appearance………………………………. Milky straw.

Odor…………………………………………………….. Fragrance.

Odor Threshold (ppm)…………………………….. N/A.

Specific Gravity (Aerosol)………………………… 0.910-0.970.

Specific Gravity (Liquid)………………………….. 0.980-1.020.

Aerosol Vapour Pressure (psig, 21°C)………. 40-50.

Vapour Density (Air=1)……………………………. > 1.

pH………………………………………………………… 7.0-9.0.

Boiling Point liquid (°C)……………………………. -11.72°C (10.9°F). (For propellant).

Melting/Freezing Point (°C)……………………… N/A.

Flash Point (°C), Method…………………………. Closed cup: -83.15 ºC (-117.7 ºF). (For propellant).

00000485 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 09: PHYSICAL AND CHEMICAL PROPERTIES

Flashback……………………………………………… No.

Evaporation Rate (n-Butyl Acetate = 1)

VOC Content…………………………………………. N/A.

Solubility in water…………………………………… Completely.

Aerosol Flame Projection………………………… No data.

Auto Ignition Temperature (°C)…………………. 460°C (860°F). (For propellant).

Lower Flammable Limit (% Vol)……………….. 1.8. (For propellant).

Upper Flammable Limit (% Vol)……………….. 9.5. (For propellant).

Coefficient of Water/Oil Distribution………….. N/A.

Viscosity……………………………………………….. N/A.

Section 10: STABILITY AND REACTIVITY

Reactivity ……………………………………………… Product not reactive under normal conditions of use.

Chemical Stability…………………………………… Material is stable under normal conditions.

Possibility of Hazardous Reactions…………… Will not occur.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge. Contact with incompatible

substances.

Incompatible Materials……………………………. Strong oxidizing agents. Strong acids. Strong bases.

Hazardous Decomposition Products…………. Carbon Monoxide, Carbon Dioxide, Phosgene, Hydrogen Chloride Gas.

Section 11: TOXICOLOGICAL INFORMATION

Ingredients LC50 LD50

Isobutane 658 mg/L (4hrs,Rat) Not available

Hydrotreated Light Petroleum Distillate 5.500 mg/L (rat- Inhl) 5.0 g/kg (rat – oral); 4.0 g/kg

(rabbit – dermal)

Propane >800,000 ppm (15 min,Rat) Not available

Information on Likely Routes of Exposure:

Routes of entry – Inhalation……………………… Yes.

Routes of entry – Skin & Eye……………………. Yes.

Routes of entry – Ingestion………………………. No.

Routes of entry – Skin Absorption……………… No.

Symptoms Related to the Physical, Chemical

and Toxicological Characteristics

Acute Toxicity………………………………………… No known significant effects.

Skin Corrosion/Irritation…………………………… Causes mild skin irritation. Prolonged contact may be more irritating.

Serious Eye Damage/Eye Irritation…………… May irritate eyes.

Respiratory or Skin Sensitization……………… Inhalation may cause respiratory tract irritation.

Germ Cell Mutagenicity…………………………… No data available to indicate product or any components present at greater than 0.1% are

mutagenic.

Carcinogenicity………………………………………. No information is available.

Reproductive Toxicity……………………………… Based on available data, the classification criteria are not met.

Specific Target Organ Toxicity – Single …….. No data available .

Exposure

Specific Target Organ Toxicity – Repeated .. No known significant effects.

Exposure

Aspiration Hazard

Chronic Effects………………………………………. Repeated or prolonged skin exposure may result in moderate irritation, drying, cracking

and defatting of the skin (dermatitis).

Section 12: ECOLOGICAL INFORMATION

Ecotoxicity…………………………………………….. May be dangerous for the environment. No data is available on the product itself. Should

not be released into the environment.

Persistence and degradability …………………. The product itself has not been tested.

Bioaccumulation Potential……………………….. The product itself has not been tested.

Mobility in Soil……………………………………….. The product itself has not been tested.

Other Adverse Effects…………………………….. None Known.

Section 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. This material and its container must be disposed of as hazardous waste. Avoid release to

the environment. Spilled material and water rinses are classified as chemical waste and

must be disposed of in accordance with current local, provincial and federal regulations.

Contents under pressure. Do not puncture, incinerate or expose to heat, even when empty.

00000485 SAFETY DATA SHEET Page 4

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.2, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY, Consumer Commodity ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.2, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY .

Section 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas. B5: Flammable Aerosol.

Canadian Environmental Protection Act ……. All ingredients listed appear on the Domestic Substances List (DSL).

(CEPA)

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. This product is considered hazardous under the OSHA Hazard Communication

Standard.

Section 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. The SDS provider assumes no responsibility for personal injury or property

damage to vendees or users or third parties, caused by the material. Such vendees or

users assume all risks with the use of the material. This product has been classified in

accordance with the hazard criteria of the CPR and the SDS contains all the information

required by the CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information System.

Prepared by ………………………………………….. Regulatory Affairs

Preparation Date……………………………………. Mar05/15

MSDS Dry Shine Ultimate Shine

SDS & Labels by TECIS www.trivalent.com

00000163 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine Ultimate Shine 400g CODE: A6-000407

SECTION 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Identity……………………………………… Dry Shine Ultimate Shine 400g

Product Item Numbers……………………………. A6-000407

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CANUTEC: (613)-996-6666 collect.

Recommended Use………………………………… Provides uniform shine on vinyl, leather, rubber and plastic surface.

Consumer Commodity…………………………….. Yes.

Hazard Ratings:

HMIS……………………………………………………. Health: 2 Fire: 4 Reactivity: 0.

NFPA Rating…………………………………………. Health: 2 Fire: 4 Reactivity: 0.

SECTION 02: HAZARDS IDENTIFICATION

Emergency Overview……………………………… Flammable. Danger. Poison. Contents under pressure. May catch fire. Contents may be

harmful. Do not swallow . Do not puncture. Do not burn. Do not get in eyes or clothing.

KEEP OUT OF REACH OF CHILDREN .

Potential Health Effects:

Eye Contact…………………………………………… May cause irritation, redness and pain.

Skin Contact …………………………………………. Can cause skin irritation. Prolonged or repeated contact may dry the skin.

Ingestion……………………………………………….. Harmful if swallowed.

Inhalation………………………………………………. Prolong Inhalation of content may cause irritation.

SECTION 03: COMPOSITION/INFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS CAS # WT. %

Heptane 142-82-5 60-100

Propane 74-98-6 10-30

Isobutane 75-28-5 10-30

Silicone 63148-62-9 5-10

SECTION 04: FIRST AID MEASURES

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Skin Contact………………………………………….. Wash thoroughly with soap and lukewarm water.

Ingestion……………………………………………….. If swallowed, get medical attention immediately. Do not induce vomiting .

Inhalation………………………………………………. If inhaled, remove to fresh air. If not breathing, give artificial respiration and obtain

immediate medical assistance.

Additional Information……………………………… Note to the doctor; treat symptomatically.

SECTION 05: FIRE FIGHTING MEASURES

Flammability Class…………………………………. Flammable.

Extinguishing Media……………………………….. Carbon dioxide, dry chemicals, foam or water fog.

Sensitivity to Mechanical Impact………………. Not expected to be sensitive.

Sensitivity to Static Discharge………………….. Not expected to be sensitive.

SECTION 06: ACCIDENTAL RELEASE MEASURES

Spills and Leaks…………………………………….. Large spill or leak is unlikely in aerosol containers. If spill or leak occurs, ventilate enclosed

spaces and disperse gas with floor-level forced-air ventilation. Exhaust vapours outdoors.

Do not smoke or operate internal combustion engines. Remove flames and heating

elements.

SDS & Labels by TECIS www.trivalent.com

00000163 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine Ultimate Shine 400g CODE: A6-000407

SECTION 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Avoid contact with heat, sparks and flame. Avoid contact with eyes, skin, and clothing.

Keep container tightly closed. Use with adequate ventilation.

SECTION 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

INGREDIENTS TWA STEL PEL STEL REL

Heptane 400 ppm 500 ppm 500 ppm Not available 85 ppm for

n-Heptane, 440 ppm

for a ceiling conc.

Propane 2,500 ppm Not available 1,000 ppm Not available 1,000 ppm

Isobutane 800 ppm 1000 ppm 800ppm Not available 800 ppm (TWA)

Silicone Not available Not available Not available Not available No data available

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Use gloves and protective clothing against cold temperature made from viton, butyl rubber,

PVC, neoprene or nitrile.

Respiratory Protection…………………………….. Not required on a short-term basis or if exhaust ventilation is provided. Use approved

NIOSH respirators for emergencies.

Appropriate Engineering Controls…………….. Local exhaust ventilation required to maintain the point of use below the Threshold Limit

Value if unprotected personnel are involved.

Exposure Limits

SECTION 09: PHYSICAL AND CHEMICAL PROPERTIES

Physical State………………………………………… Aerosol.

Physical Appearance………………………………. Clear mist.

Odour…………………………………………………… Hydrocarbons.

Odour Threshold (ppm)…………………………… Not available.

pH………………………………………………………… Not applicable.

Vapour Pressure (psig)…………………………… 60- 80.

Vapour Density (Air=1)……………………………. Not available.

Evaporation Rate (n-Butyl Acetate = 1)……… > 1 .

Initial Boiling Point/Boiling Range (°C)………. 140-150.

VOC Content…………………………………………. Not available.

Specific Gravity (Liquid)………………………….. 0.710-0.770 .

Specific Gravity (Aerosol)………………………… 0.620- 0.660.

Solubility in water…………………………………… Nil.

Aerosol Flame Projection………………………… Not available .

Auto Ignition Temperature (Propellant), °C… 470.85 °C (888.5 °F) .

Flashback……………………………………………… Yes.

Flash Point (°C), Method…………………………. -104 °C (-156°F).

Lower Flammable Limit (% Vol)……………….. 2.1.

Upper Flammable Limit (% Vol)……………….. 9.5.

SECTION 10: STABILITY AND REACTIVITY

Chemical Stability…………………………………… Stable at normal temperatures and pressures.

Incompatible Materials……………………………. Strong oxidizing agents.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge.

Hazardous Decomposition Products…………. May form carbon dioxide and carbon monoxide, various hydrocarbons.

Possibility of Hazardous Reactions…………… Will not occur.

SECTION 11: TOXICOLOGICAL INFORMATION

INGREDIENTS LC50 LD50

Heptane 103,000 mg/L (Rat,4hr) >15,000 mg/kg (rat – oral); >2,000

mg/kg (Dermal,Rabbit)

Propane >800,000 ppm (15 min,Rat) Not available

Isobutane 658 mg/L (4hrs,rat) Not available

Silicone >2,000 mg/kg (rabbit – oral) >15,400 mg/kg (rat – oral)

Route of Exposure………………………………….. Skin contact, Eye contact, Inhalation and Ingestion.

SDS & Labels by TECIS www.trivalent.com

00000163 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine Ultimate Shine 400g CODE: A6-000407

SECTION 11: TOXICOLOGICAL INFORMATION

Effects of Acute Exposure……………………….. High vapor/aerosol concentrations may be irritating to eyes. Prolonged or repeated contact

with skin may cause redness, itching, irritation and eczema/chapping. In high

concentrations, vapors and aerosol mists have a narcotic effect and may cause headache,

fatigue, dizziness and nausea. Ingestion may result in vomiting.

Chronic Effects………………………………………. Organic solvents may be absorbed into the body by inhalation and ingestion and cause

permanent damage to the nervous system, including the brain. Prolong contact may defat

and dry the skin, leading to discomfort and dermatitis .

Carcinogenicity………………………………………. Not classified as carcinogenic by ACGIH, IARC, OSHA or NTP.

Reproductive Toxicity……………………………… No information is available, and no adverse effects are expected.

Teratogenicity………………………………………… No information is available, and no adverse effects are expected.

Germ Cell Mutagenicity…………………………… No information is available, and no adverse effects are expected.

Toxicological Data

SECTION 12: ECOLOGICAL INFORMATION

Environmental……………………………………….. Very toxic to aquatic organisms may cause long-term adverse effects in the aquatic

environment. This material and its container must be disposed of as hazardous waste.

Avoid release to the environment. Heptane: Toxicity to fish: LC50 1.284 mg/L, 96 hrs;

Toxicity to other aquatic invertebrates: 0.1 mg/L, 96 hrs; Toxicity to algae: EL50 4.338

mg/L, 72 hrs.

SECTION 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. Dispose in accordance with local, provincial and federal regulations.

SECTION 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.1, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.1, UN1950, LTD QTY, Consumer commodity ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.1, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.1, UN1950, LTD QTY.

SECTION 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas. B5: Flammable Aerosol. D2B: Material causing

other toxic Materials.

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. OSHA (29CFR 1910.1200) Classification: Compressed Gas. HIMS

Classifications: see section 01.

SECTION 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. Empack assumes no responsibility for personal injury or property damage to

vendees or users or third parties, caused by the material. Such vendees or users assume

all risks with the use of the material. This product has been classified in accordance with

the hazard criteria of the CPR and the SDS contains all the information required by the

CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information STOT: System.Specific Target Organ Toxicity.

Prepared by ………………………………………….. Regulatory Affairs

 

Preparation Date……………………………………. NOV 16/2015

MSDS Dry Shine Quick Wax

Powered by www.trivalent.com

00000645 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Quick Wax- 490g CODE: A6-000510

SECTION 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Item Numbers……………………………. A6-000510

Product Identity……………………………………… Quick Wax- 490g

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CHEM TREC: 800-424-9300.

Recommended Use………………………………… Wax for vehicles.

Chemical Family…………………………………….. Mixture.

SECTION 02: HAZARDS IDENTIFICATION

Hazard Classification:

Physical Hazards……………………………………. Gases Under Pressure – Liquefied Gas . Aerosols – Category 3.

Health Hazards………………………………………. Skin Irritation – Category 3. Eye Damage/Irritation – Category 2B. Acute Toxicity Oral –

Category 5.

Environmental Hazards…………………………… Not Classified.

Label Elements:

Signal Word…………………………………………… WARNING.

Hazard Statement………………………………….. Contains gas under pressure; may explode if heated. Pressurized container: may burst if

heated. May be harmful if swallowed. Causes eye irritation.

Precautionary Statements:

Prevention…………………………………………….. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No

smoking. Do not pierce or burn, even after use. Wash hand thoroughly after handling.

Response……………………………………………… IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if

present and easy to do. Continue rinsing. If eye irritation persists: Get medical

advice/attention. Call a POISON CENTER if you feel unwell.

Storage…………………………………………………. Protect from sunlight. Do not expose to temperatures exceeding 50°C /122°F. Store in a

well ventilated place .

Disposal………………………………………………… Not applicable.

Hazard(s) not otherwise classified (HNOC).. None Known.

SECTION 03: COMPOSITION/INFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS CAS # WT. %

Dimethyl Ether 115-10-6 10-30

D-Limonene 5989-27-5 1-5

Surfactants Mix. 1-5

SECTION 04: FIRST AID MEASURES

Inhalation………………………………………………. If inhaled, remove to fresh air. If not breathing, give artificial respiration and obtain

immediate medical assistance.

Skin Contact………………………………………….. Wash exposed area with soap and water. Remove contaminated clothing. If irritation or

redness develops, seek medical attention.

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Ingestion……………………………………………….. Ingestion is not a likely route of exposure. If ingested, do not induce vomiting, get medical

attention.

Most important symptoms/effects, acute and Immediate medical attention is required.

delayed

Powered by www.trivalent.com

00000645 SAFETY DATA SHEET Page 2

PRODUCT: Quick Wax- 490g CODE: A6-000510

SECTION 04: FIRST AID MEASURES

Indication of immediate medical attention and Provide general supportive measures and treat symptomatically. In case of shortness of

special treatment needed breath give oxygen. Keep victim warm. Keep victim under observation. Symptoms may be

delayed.

SECTION 05: FIRE FIGHTING MEASURES

Suitable Extinguishing Media…………………… Dry chemical powder. Carbon dioxide. Foam, water spray or fog.

Unsuitable Extinguishing Media……………….. Do not use water jet as an extinguisher, as this will spread the fire.

Specific Hazards Arising from the Chemical. Contents under pressure. Pressurized container may explode when exposed to heat or

flame.

Special Protective Equipment and …………… Firefighters must use standard protective equipment including flame retardant coat, helmet

Precautions for Firefighters with water to prevent vapor pressure build up. For massive fire in cargo area, use

unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.

General Fire Hazards……………………………… Non Flammable aerosol, but contains flammable propellant.

SECTION 06: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment No action shall be taken involving any personal risk or without suitable training. Evacuate

and Emergency Procedures surrounding areas. Keep unnecessary and unprotected personnel from entering. Avoid

walking through spilled material. Avoid breathing vapor or mist. Provide adequate

ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate

personal protective equipment (see Section 08).

Methods and Materials for Containment and Spill areas may be slippery. Use care to avoid falls or other accidents . Contain the spill.

Cleaning Up Clean up the spill area with detergent and water. Once spilled material has been collected,

use rags or other suitable material to clean spill area. Rags should be properly disposed

off.

Environmental Precautions……………………… Keep out of drains, sewers, ditches, and waterways. Minimize use of water to prevent

environmental contamination.

SECTION 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is

missing or defective. Do not spray on a naked flame or any other incandescent material.

Do not pressurize, cut, weld, braze, solder, drill, grind, or expose empty containers to heat,

sparks or open flames. Avoid contact with eyes, skin, and clothing. Avoid breathing vapour

of this product. Avoid contact with skin and eyes. Avoid prolonged exposure. Use in

well-ventilated areas.

Conditions for Safe Storage including any … Store locked up. Pressurized container. Protect from sunlight and do not expose to

Incompatibilities temperatures exceeding 50°C (122°F). Do not puncture, incinerate or crush. Do not handle

or store near an open flame, heat or other sources of ignition. Store away from

incompatible materials (see Section 10).

SECTION 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

INGREDIENTS TWA STEL PEL STEL REL

Dimethyl Ether 1000 ppm (8hrs) Not available Not available Not available Not available

D-Limonene Not available Not available Not available Not available Not available

Surfactants Not available Not available Not available Not available Not available

Appropriate Engineering Controls…………….. Local exhaust ventilation required to maintain the point of use below the Threshold Limit

Value if unprotected personnel are involved.

Individual Protection Measures:

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Chemical resistant gloves are recommended. Avoid contact with the skin. Wear

appropriate chemical resistant clothing.

Respiratory Protection…………………………….. Use dust and mist respirator.

Thermal Hazards……………………………………. None Known.

General Hygiene Considerations……………… When using, do not eat, drink or smoke. Always observe good personal hygiene measures,

such as washing after handling the material and before eating, drinking, and/or smoking.

Routinely wash work clothing and protective equipment prior to use.

Powered by www.trivalent.com

00000645 SAFETY DATA SHEET Page 3

PRODUCT: Quick Wax- 490g CODE: A6-000510

SECTION 09: PHYSICAL AND CHEMICAL PROPERTIES

Form…………………………………………………….. Aerosol.

Physical Appearance………………………………. Fine spray mist.

Odor…………………………………………………….. Fragrance.

Odor Threshold (ppm)…………………………….. N/A.

Specific Gravity (Aerosol)………………………… 0.910-0.970.

Specific Gravity (Liquid)………………………….. 0.980-1.020.

Aerosol Vapour Pressure (psig, 21°C)………. 40-50.

Vapour Density (Air=1)……………………………. > 1.

pH………………………………………………………… 7.0- 9.0.

Boiling Point liquid (°C)……………………………. starts 93ºC (199.40ºF).

Melting/Freezing Point (°C)……………………… N/A.

Flash Point (°C), Method…………………………. Closed cup: -83.15 ºC (-117.7 ºF). (For propellant).

Flashback……………………………………………… No.

Evaporation Rate (n-Butyl Acetate = 1)

VOC Content…………………………………………. N/A.

Solubility in water…………………………………… Completely.

Aerosol Flame Projection………………………… No data.

Auto Ignition Temperature (°C)…………………. (propellant). 350°C (662°F).

Lower Flammable Limit (% Vol)……………….. (propellant). 3.3 .

Upper Flammable Limit (% Vol)……………….. (propellant). 26.2.

Coefficient of Water/Oil Distribution………….. N/A.

Viscosity……………………………………………….. Very fluid.

SECTION 10: STABILITY AND REACTIVITY

Reactivity ……………………………………………… Product not reactive under normal conditions of use.

Chemical Stability…………………………………… Material is stable under normal conditions.

Possibility of Hazardous Reactions…………… Will not occur.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge. Contact with incompatible

substances.

Incompatible Materials……………………………. Strong oxidizing agents. Strong acids. Strong bases.

Hazardous Decomposition Products…………. Carbon Monoxide, Carbon Dioxide, Phosgene, Hydrogen Chloride Gas.

SECTION 11: TOXICOLOGICAL INFORMATION

INGREDIENTS LC50 LD50

Dimethyl Ether 308 mg/L (4hrs,Rat) Not available

D-Limonene 5000 mg/kg (Rat) >5,000 mg/kg (Dermal,Rabbit)

Surfactants Not available Not available

Information on Likely Routes of Exposure:

Routes of entry – Inhalation……………………… Yes.

Routes of entry – Skin & Eye……………………. Yes.

Routes of entry – Ingestion………………………. No.

Routes of entry – Skin Absorption……………… No.

Symptoms Related to the Physical, Chemical

and Toxicological Characteristics

Acute Toxicity………………………………………… No known significant effects.

Skin Corrosion/Irritation…………………………… Causes mild skin irritation. Prolonged contact may be more irritating.

Serious Eye Damage/Eye Irritation…………… May irritate eyes.

Respiratory or Skin Sensitization……………… Inhalation may cause respiratory tract irritation.

Germ Cell Mutagenicity…………………………… No data available to indicate product or any components present at greater than 0.1% are

mutagenic.

Carcinogenicity………………………………………. No information is available.

Reproductive Toxicity……………………………… Based on available data, the classification criteria are not met.

STOT – Single Exposure…………………………. No data available .

STOT – Repeated Exposure…………………….. No known significant effects.

Aspiration Hazard

Chronic Effects………………………………………. Repeated or prolonged skin exposure may result in moderate irritation, drying, cracking

and defatting of the skin (dermatitis).

SECTION 12: ECOLOGICAL INFORMATION

Ecotoxicity…………………………………………….. May be dangerous for the environment. No data is available on the product itself. Should

not be released into the environment.

Persistence and degradability …………………. The product itself has not been tested.

Bioaccumulation Potential……………………….. The product itself has not been tested.

Mobility in Soil……………………………………….. The product itself has not been tested.

Powered by www.trivalent.com

00000645 SAFETY DATA SHEET Page 4

PRODUCT: Quick Wax- 490g CODE: A6-000510

SECTION 12: ECOLOGICAL INFORMATION

Other Adverse Effects…………………………….. None Known.

SECTION 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. This material and its container must be disposed of as hazardous waste. Avoid release to

the environment. Spilled material and water rinses are classified as chemical waste and

must be disposed of in accordance with current local, provincial and federal regulations.

Contents under pressure. Do not puncture, incinerate or expose to heat, even when empty.

SECTION 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.2, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY, Consumer Commodity ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.2, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY .

SECTION 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas.

Canadian Environmental Protection Act ……. All ingredients listed appear on the Domestic Substances List (DSL).

(CEPA)

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. This product is considered hazardous under the OSHA Hazard Communication

Standard.

SECTION 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herein is based on data considered accurate. No guarantee or

warranty is expressed or implied regarding the accuracy of this data or the results obtained

from the use thereof. The SDS provider assumes no responsibility for personal injury or

property damage to vendees or users or third parties, caused by the material. Such

vendees or users assume all risks with the use of the material. This product has been

classified in accordance with the hazard criteria of the CPR and the SDS contains all the

information required by the CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHMIS: Workplace Hazardous

Materials Information System STOT: Specific Target Organ Toxicity.

Prepared by ………………………………………….. Regulatory Affairs

 

Latest Revision ……………………………………… SEP 09/2016

 

MSDS Dry Shine Leather Cleaner and Conditioner

SDS & Labels by TECIS www.trivalent.com

00000381 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine Leather Cleaner and Conditioner 375ml CODE: A6-000411

SECTION 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Identity……………………………………… Dry Shine Leather Cleaner and Conditioner 375ml

Product Item Numbers……………………………. A6-000411

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CANUTEC: (613)-996-6666 collect.

Recommended Use………………………………… Leather cleaner and conditioner .

Consumer Commodity…………………………….. Yes.

Hazard Ratings:

HMIS……………………………………………………. Health: 1 Fire: 0 Reactivity: 0.

NFPA Rating…………………………………………. Health: 1 Fire: 0 Reactivity: 0.

SECTION 02: HAZARDS IDENTIFICATION

Emergency Overview……………………………… May cause skin and eye irritation. KEEP OUT OF REACH OF CHILDREN .

Potential Health Effects:

Eye Contact…………………………………………… May cause irritation, redness and pain.

Skin Contact …………………………………………. Can cause skin irritation. Prolonged or repeated contact may dry the skin.

Ingestion……………………………………………….. Harmful if swallowed.

Inhalation………………………………………………. Inhalation of vapour may cause irritation. May cause drowsiness or dizziness.

SECTION 03: COMPOSITION/INFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS CAS # WT. %

Propylene glycol 57-55-6 1-5

Surfactants Mix 1-5

Silicone Proprietary 1-5

SECTION 04: FIRST AID MEASURES

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Skin Contact………………………………………….. Wash thoroughly with soap and lukewarm water.

Ingestion……………………………………………….. If ingested, do not induce vomiting, get medical attention.

Inhalation………………………………………………. Move victim to fresh air. If breathing is difficult, give oxygen and get medical attention.

Additional Information……………………………… Note to the doctor; treat symptomatically.

SECTION 05: FIRE FIGHTING MEASURES

Flammability Class…………………………………. Non-Flammable.

Extinguishing Media……………………………….. Small Fire: Use Dry Chemical. Large Fire: Use water spray or fog.

Sensitivity to Mechanical Impact………………. Not expected to be sensitive.

Sensitivity to Static Discharge………………….. Not expected to be sensitive.

SECTION 06: ACCIDENTAL RELEASE MEASURES

Spills and Leaks…………………………………….. Clean up the spill area with detergent and water.

SECTION 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Do not breathe vapour or mist. Avoid contact with eyes, skin, and clothing. Use with

adequate ventilation. Do not enter confined spaces unless adequately ventilated.

SDS & Labels by TECIS www.trivalent.com

00000381 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine Leather Cleaner and Conditioner 375ml CODE: A6-000411

SECTION 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

INGREDIENTS TWA STEL PEL STEL REL

Propylene glycol Not available Not available Not available Not available Not available

100 ppm

Surfactants Not available Not available Not available Not available Not available

Silicone not established not established not established not established not established

not established

Eye/Face Protection……………………………….. Not normally required. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Not needed at normal use conditions.

Respiratory Protection…………………………….. Not required on a short-term basis or if exhaust ventilation is provided.

Appropriate Engineering Controls…………….. Good general ventilation should be used. Ventilation rates should be matched to

conditions. Use local exhaust ventilation to maintain airborne levels below the Threshold

Limit Value.

Exposure Limits

SECTION 09: PHYSICAL AND CHEMICAL PROPERTIES

Physical State………………………………………… Lotion.

Physical Appearance………………………………. White lotion.

Odour…………………………………………………… Fragrance.

Odour Threshold (ppm)…………………………… Not available.

pH………………………………………………………… 6.0 – 8.0.

Internal can pressure (psig)……………………… Not applicable.

Vapour Density (Air=1)……………………………. > 1.

Evaporation Rate (n-Butyl Acetate = 1)……… < 1 (n-Butyl Acetate = 1).

Initial Boiling Point/Boiling Range (°C)………. 95-105 °C (203-221 °F).

VOC Content…………………………………………. Not available.

Specific Gravity (Liquid)………………………….. 0.940- 1.000.

Specific Gravity (Aerosol)………………………… Not applicable.

Solubility in water…………………………………… Soluble in water.

Aerosol Flame Projection………………………… No data.

Auto Ignition Temperature (Propellant), °C… No data.

Flashback……………………………………………… No.

Flash Point (°C), Method…………………………. Not applicable.

Lower Flammable Limit (% Vol)……………….. Not applicable.

Upper Flammable Limit (% Vol)……………….. Not applicable.

SECTION 10: STABILITY AND REACTIVITY

Chemical Stability…………………………………… Stable at normal temperatures and pressures.

Incompatible Materials……………………………. Strong oxidizing agents.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge.

Hazardous Decomposition Products…………. May form carbon dioxide and carbon monoxide, various hydrocarbons.

Possibility of Hazardous Reactions…………… Will not occur.

SECTION 11: TOXICOLOGICAL INFORMATION

INGREDIENTS LC50 LD50

Propylene glycol Not available 20,000 mg/kg (oral, rat)

Surfactants Not available Not available

Silicone not established not established

Route of Exposure………………………………….. Eye contact, ingestion.

Effects of Acute Exposure……………………….. May cause dermatitis, irritation to eyes, dizziness, and vomiting.

Chronic Effects………………………………………. No known adverse effects .

Carcinogenicity………………………………………. None known when used below acute toxicity limit.

Reproductive Toxicity……………………………… No information is available, and no adverse effects are expected.

Teratogenicity………………………………………… No information is available, and no adverse effects are expected.

Germ Cell Mutagenicity…………………………… No information is available, and no adverse effects are expected.

Toxicological Data

SDS & Labels by TECIS www.trivalent.com

00000381 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine Leather Cleaner and Conditioner 375ml CODE: A6-000411

SECTION 12: ECOLOGICAL INFORMATION

Environmental……………………………………….. Avoid release to the environment.

SECTION 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. Dispose in accordance with local, provincial and federal regulations.

SECTION 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… Not currently regulated.

DOT (US-Road)……………………………………… Not currently regulated.

IMDG (International- Marine)……………………. Not currently regulated.

IATA (International- Air)…………………………… Not currently regulated.

SECTION 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. Not regulated. CPR (Canadian Controlled Product Regulations): All

ingredients are CEPA approved for import to Canada. This product has been classified in

accordance with the hazard criteria of the CPR and this SDS contains all information

required by CPR.

US Regulations……………………………………… OSHA (29CFR 1910.1200). HMIS classification see section 01.

SECTION 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. Empack assumes no responsibility for personal injury or property damage to

vendees or users or third parties, caused by the material. Such vendees or users assume

all risks with the use of the material. This product has been classified in accordance with

the hazard criteria of the CPR and the SDS contains all the information required by the

CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information STOT: System.Specific Target Organ Toxicity.

Prepared by ………………………………………….. Regulatory Affairs

 

Preparation Date……………………………………. NOV 16/2015

MSDS Dry Shine Foaming Glass Cleaner

SDS & Labels by TECIS www.trivalent.com

00000148 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine Foaming Glass Cleaner 517g CODE: A6-000409

SECTION 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Item Numbers……………………………. A6-000409

Product Identity……………………………………… Dry Shine Foaming Glass Cleaner 517g

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CANUTEC: (613)-996-6666 collect.

Recommended Use………………………………… Cleans windows, mirrors, windshields, tile, porcelain, stainless steel, chrome.

Consumer Commodity…………………………….. Yes.

Hazard Ratings:

HMIS……………………………………………………. Health: 1 Fire: 1 Reactivity: 0.

NFPA Rating…………………………………………. Health: 1 Fire: 1 Reactivity: 0.

SECTION 02: HAZARDS IDENTIFICATION

Emergency Overview……………………………… Caution. Poison. Contents under pressure. Container may explode if heated. May irritate

eyes and skin. Do not breathe fumes. Do not puncture. Do not burn. Do not get in eyes,

skin or clothing. KEEP OUT OF REACH OF CHILDREN .

Potential Health Effects:

Eye Contact…………………………………………… May cause irritation, redness and pain.

Skin Contact …………………………………………. Can cause skin irritation. Prolonged or repeated contact may dry the skin.

Ingestion……………………………………………….. Can be harmful if ingested .

Inhalation………………………………………………. Prolong Inhalation of content may cause irritation.

SECTION 03: COMPOSITION/INFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS CAS # WT. %

Isopropyl Alcohol 67-63-0 7-13

Isobutane 75-28-5 5-10

2-Butoxyethanol 111-76-2 3-7

SECTION 04: FIRST AID MEASURES

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Skin Contact………………………………………….. If symptoms persist, seek medical attention. Wash thoroughly with soap and lukewarm

water.

Ingestion……………………………………………….. If swallowed, get medical attention immediately. Do not induce vomiting .

Inhalation………………………………………………. Move victim to fresh air. If breathing has stopped, give artificial respiration. If heartbeat

absent, give external cardiac compression. Monitor breathing and pulse. If symptoms

persist, call a physician.

Additional Information……………………………… Note to the doctor; treat symptomatically.

SECTION 05: FIRE FIGHTING MEASURES

Flammability Class…………………………………. Non-flammable (but contains flammable gas).

Extinguishing Media……………………………….. Not flammable. Use regular extinguishing media whenever needed.

Sensitivity to Mechanical Impact………………. Not expected to be sensitive.

Sensitivity to Static Discharge………………….. Not expected to be sensitive.

SECTION 06: ACCIDENTAL RELEASE MEASURES

Spills and Leaks…………………………………….. Put on appropriate personal protective equipment (see Section 08). Eliminate all sources of

ignition and ventilate area. Contain spillage, and then collect with non-combustible

absorbent material (e.g. sand, earth, diatomaceous earth, vermiculite) and place in

container for disposal according to local/national regulations (see Section 13).

SDS & Labels by TECIS www.trivalent.com

00000148 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine Foaming Glass Cleaner 517g CODE: A6-000409

SECTION 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Do not breathe vapour or mist. Avoid contact with eyes, skin, and clothing. Use with

adequate ventilation. Do not enter confined spaces unless adequately ventilated.

SECTION 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

INGREDIENTS TWA STEL PEL STEL REL

Isopropyl Alcohol 400 ppm (983 mg/m3) 500 ppm (1230 400 ppm (980 500 ppm (1,225 400 ppm (TWA)

mg/m3) mg/m3) mg/m3)

Isobutane 800 ppm 1000 ppm 800ppm Not available 800 ppm (TWA)

2-Butoxyethanol 20 ppm Not available 50 ppm Not available Not available

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Normally, no hand protection is required; however, prolonged or repeated contact with skin

use chemical resistant gloves conforming to appropriate regulations. Observe the

instructions regarding permeability and breakthrough time that are provided by the supplier

of the gloves.

Respiratory Protection…………………………….. Typical use of this product under normal conditions does not require the use of respiratory

protection. If airborne concentrations are above the applicable exposure limits (listed

below), use NIOSH approved respiratory protection .

Appropriate Engineering Controls…………….. Good general ventilation should be used. Ventilation rates should be matched to

conditions. Use local exhaust ventilation to maintain airborne levels below the Threshold

Limit Value.

Exposure Limits

SECTION 09: PHYSICAL AND CHEMICAL PROPERTIES

Physical State………………………………………… Aerosol.

Physical Appearance………………………………. Cloudy liquid .

Odour…………………………………………………… Fragrance.

Odour Threshold (ppm)…………………………… Not determined.

pH………………………………………………………… 6.0 – 8.0.

Internal can pressure (psig)……………………… 50-70.

Vapour Density (Air=1)……………………………. > 1.

Evaporation Rate (n-Butyl Acetate = 1)……… No data.

Initial Boiling Point/Boiling Range (°C)………. Not available.

VOC Content…………………………………………. 95-100 %wt.

Specific Gravity …………………………………….. 0.980-1.020.

Specific Gravity (Aerosol)………………………… 0.910-0.970.

Solubility in water…………………………………… Soluble in water.

Aerosol Flame Projection………………………… Not available .

Auto Ignition Temperature (Propellant), °C… 460°C (860°F).

Flashback……………………………………………… No data .

Flash Point (°C), Method…………………………. Closed cup: -83.15 ºC (-117.7 ºF).

Lower Flammable Limit (% Vol)……………….. 1.8.

Upper Flammable Limit (% Vol)……………….. 8.5.

SECTION 10: STABILITY AND REACTIVITY

Chemical Stability…………………………………… Stable at normal temperatures and pressures.

Incompatible Materials……………………………. Strong oxidizing agents.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge.

Hazardous Decomposition Products…………. May form carbon dioxide and carbon monoxide, various hydrocarbons.

Possibility of Hazardous Reactions…………… Will not occur.

SECTION 11: TOXICOLOGICAL INFORMATION

INGREDIENTS LC50 LD50

Isopropyl Alcohol >20,000 ppm (4hrs-rat) 4,700 – 5,800 mg/kg (oral,rat)

Isobutane 658 mg/L (4hrs,rat) Not available

2-Butoxyethanol 450 ppm (4hr,rat) 470 mg/kg (4hr,oral,rat)

Route of Exposure………………………………….. Eye contact, Skin contact, Skin absorption, Inhalation, and Ingestion.

Effects of Acute Exposure……………………….. May cause dermatitis, irritation to eyes, dizziness, and vomiting.

Chronic Effects………………………………………. No known adverse effects .

SDS & Labels by TECIS www.trivalent.com

00000148 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine Foaming Glass Cleaner 517g CODE: A6-000409

SECTION 11: TOXICOLOGICAL INFORMATION

Carcinogenicity………………………………………. Not classified as carcinogenic by ACGIH, IARC, OSHA or NTP.

Reproductive Toxicity……………………………… No information is available, and no adverse effects are expected. Reproductive Toxicity.

Teratogenicity………………………………………… No information is available, and no adverse effects are expected.

Germ Cell Mutagenicity…………………………… No information is available, and no adverse effects are expected.

Toxicological Data

SECTION 12: ECOLOGICAL INFORMATION

Environmental……………………………………….. Isopropanol alcohol: Toxicity to fish: LC50 9,640 mg/L, 96 hrs; Toxicity to other aquatic

invertebrates: 5,102 mg/L, 96 hrs; Toxicity to algae: EL50 >2,000 mg/L, 72 hrs. Avoid

release to the environment.

Ecotoxicity

SECTION 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. Dispose in accordance with local, provincial and federal regulations.

SECTION 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.2, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY, Consumer Commodity ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.2, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY .

SECTION 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas. D2B: Material causing other toxic Materials.

CPR (Canadian Controlled Product Regulations): All ingredients are CEPA approved for

import to Canada. This product has been classified in accordance with the hazard criteria

of the CPR and this SDS contains all information required by CPR. IDL (Canadian

Ingredient Disclosure List): Component(s) of this product identified by CAS number and

listed on the Canadian Ingredient Disclosure List (section 03).

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. OSHA (29CFR 1910.1200) Classification: Compressed Gas. HIMS

Classifications: see section 01.

SECTION 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. Empack assumes no responsibility for personal injury or property damage to

vendees or users or third parties, caused by the material. Such vendees or users assume

all risks with the use of the material. This product has been classified in accordance with

the hazard criteria of the CPR and the SDS contains all the information required by the

CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information STOT: System.Specific Target Organ Toxicity.

Prepared by ………………………………………….. Regulatory Affairs

 

Preparation Date……………………………………. NOV 16/2015

MSDS Dry Shine Foaming Tire Shine

SDS & Labels by TECIS www.trivalent.com

00000280 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine Foaming Tire Shine 500g CODE: A6-000410

SECTION 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Identity……………………………………… Dry Shine Foaming Tire Shine 500g

Product Item Numbers……………………………. A6-000410

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CANUTEC: (613)-996-6666 collect.

Recommended Use………………………………… Cleans, shines and protects your tires in one easy step.

Hazard Ratings:

HMIS……………………………………………………. Health: 2 Fire: 4 Reactivity: 0.

NFPA Rating…………………………………………. Health: 2 Fire: 4 Reactivity: 0.

SECTION 02: HAZARDS IDENTIFICATION

Emergency Overview……………………………… Danger. Poison. Contents harmful . Contents under pressure. Container may explode if

heated. Do not puncture. Do not burn. Do not get in eyes, skin or clothing. Do not swallow .

KEEP OUT OF REACH OF CHILDREN .

Potential Health Effects:

Eye Contact…………………………………………… May cause irritation, redness and pain.

Skin Contact …………………………………………. Can cause skin irritation. Prolonged or repeated contact may dry the skin.

Ingestion……………………………………………….. Harmful if swallowed.

Inhalation………………………………………………. Inhalation may cause nasal and respiratory irritation.

SECTION 03: COMPOSITION/INFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS CAS # WT. %

Silicone 63148-62-9 15-40

Isobutane 75-28-5 10-30

Propane 74-98-6 1-5

SECTION 04: FIRST AID MEASURES

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Skin Contact………………………………………….. Wash thoroughly with soap and lukewarm water. If symptoms persist, seek medical

attention.

Ingestion……………………………………………….. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting.

Inhalation………………………………………………. Move victim to fresh air. If breathing has stopped, give artificial respiration. If heartbeat

absent, give external cardiac compression. Monitor breathing and pulse. If symptoms

persist, call a physician.

Additional Information……………………………… Note to the doctor; treat symptomatically.

SECTION 05: FIRE FIGHTING MEASURES

Flammability Class…………………………………. Non-Flammable but contains flammable propellant.

Extinguishing Media……………………………….. Not flammable. Use regular extinguishing media whenever needed.

Sensitivity to Mechanical Impact………………. Not expected to be sensitive.

Sensitivity to Static Discharge………………….. Not expected to be sensitive.

SECTION 06: ACCIDENTAL RELEASE MEASURES

Spills and Leaks…………………………………….. Put on appropriate personal protective equipment (see Section 08). Eliminate all sources of

ignition and ventilate area. Contain spillage, and then collect with non-combustible

absorbent material (e.g. sand, earth, diatomaceous earth, vermiculite) and place in

container for disposal according to local/national regulations (see Section 13).

SDS & Labels by TECIS www.trivalent.com

00000280 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine Foaming Tire Shine 500g CODE: A6-000410

SECTION 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Do not breathe vapour or mist. Avoid contact with eyes, skin, and clothing. Keep container

tightly closed. Use with adequate ventilation. Do not store in temperatures above 120°F

(50°C).

SECTION 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

INGREDIENTS TWA STEL PEL STEL REL

Silicone Not available Not available Not available Not available No data available

Isobutane 800 ppm 1000 ppm 800ppm Not available 800 ppm (TWA)

Propane 2,500 ppm Not available 1,000 ppm Not available 1,000 ppm

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Normally, no hand protection is required; however, prolonged or repeated contact with skin

use chemical resistant gloves conforming to appropriate regulations. Observe the

instructions regarding permeability and breakthrough time that are provided by the supplier

of the gloves.

Respiratory Protection…………………………….. Typical use of this product under normal conditions does not require the use of respiratory

protection. If airborne concentrations are above the applicable exposure limits (listed

below), use NIOSH approved respiratory protection .

Appropriate Engineering Controls…………….. Good general ventilation should be used. Ventilation rates should be matched to

conditions. Use local exhaust ventilation to maintain airborne levels below the Threshold

Limit Value.

Exposure Limits

SECTION 09: PHYSICAL AND CHEMICAL PROPERTIES

Physical State………………………………………… Aerosol.

Physical Appearance………………………………. Milky white .

Odour…………………………………………………… Hydrocarbons.

Odour Threshold (ppm)…………………………… Not available.

pH………………………………………………………… 8.0 – 9.0.

Internal can pressure (psig)……………………… 80-120.

Vapour Density (Air=1)……………………………. >1.

Evaporation Rate (n-Butyl Acetate = 1)……… No data.

Initial Boiling Point/Boiling Range (°C)………. 140°C- 150°C.

VOC Content…………………………………………. Not available.

Specific Gravity (Liquid)………………………….. 0.940- 1.000.

Specific Gravity (Aerosol)………………………… 0.910-0.970.

Solubility in water…………………………………… Dispersible in water.

Aerosol Flame Projection………………………… Not available .

Auto Ignition Temperature (Propellant), °C… 460°C (860°F).

Flashback……………………………………………… No data .

Flash Point (°C), Method…………………………. Closed cup: -83.15 ºC (-117.7 ºF).

Lower Flammable Limit (% Vol)……………….. 1.8.

Upper Flammable Limit (% Vol)……………….. 9.5.

SECTION 10: STABILITY AND REACTIVITY

Chemical Stability…………………………………… Stable at normal temperatures and pressures.

Incompatible Materials……………………………. Strong oxidizing agents.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge.

Hazardous Decomposition Products…………. May form carbon dioxide and carbon monoxide, various hydrocarbons.

Possibility of Hazardous Reactions…………… Will not occur.

SECTION 11: TOXICOLOGICAL INFORMATION

INGREDIENTS LC50 LD50

Silicone >2,000 mg/kg (rabbit – oral) >15,400 mg/kg (rat – oral)

Isobutane 658 mg/L (4hrs,rat) Not available

Propane >800,000 ppm (15 min,Rat) Not available

Route of Exposure………………………………….. Skin contact, Eye contact, Inhalation and Ingestion.

SDS & Labels by TECIS www.trivalent.com

00000280 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine Foaming Tire Shine 500g CODE: A6-000410

SECTION 11: TOXICOLOGICAL INFORMATION

Effects of Acute Exposure……………………….. High vapor/aerosol concentrations may be irritating to eyes. Prolonged or repeated contact

with skin may cause redness, itching, irritation and eczema/chapping. In high

concentrations, vapors and aerosol mists have a narcotic effect and may cause headache,

fatigue, dizziness and nausea. Ingestion may result in vomiting.

Chronic Effects………………………………………. No known adverse effects .

Carcinogenicity………………………………………. Not classified as carcinogenic by ACGIH, IARC, OSHA or NTP.

Reproductive Toxicity……………………………… No information is available, and no adverse effects are expected.

Teratogenicity………………………………………… No information is available, and no adverse effects are expected.

Germ Cell Mutagenicity…………………………… No information is available, and no adverse effects are expected.

Toxicological Data

SECTION 12: ECOLOGICAL INFORMATION

Environmental……………………………………….. This product has not been tested. Based on information available on its ingredients, no

adverse environmental impact is anticipated under intended use in accordance with

instructions. Avoid release to the environment.

SECTION 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. Dispose in accordance with local, provincial and federal regulations.

SECTION 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.2, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY, Consumer Commodity ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.2, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.2, UN1950, LTD QTY .

SECTION 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas. D2B: Material causing other toxic Materials.

CPR (Canadian Controlled Product Regulations): All ingredients are CEPA approved for

import to Canada. This product has been classified in accordance with the hazard criteria

of the CPR and this SDS contains all information required by CPR. IDL (Canadian

Ingredient Disclosure List): Component(s) of this product identified by CAS number and

listed on the Canadian Ingredient Disclosure List (section 03).

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. OSHA (29CFR 1910.1200) Classification: Compressed Gas. HIMS

Classifications: see section 01.

SECTION 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. Empack assumes no responsibility for personal injury or property damage to

vendees or users or third parties, caused by the material. Such vendees or users assume

all risks with the use of the material. This product has been classified in accordance with

the hazard criteria of the CPR and the SDS contains all the information required by the

CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information STOT: System.Specific Target Organ Toxicity.

Prepared by ………………………………………….. Regulatory Affairs

 

Preparation Date……………………………………. NOV 16/2015

MSDS Dry Shine Bug & Tar Remover

SDS & Labels by TECIS www.trivalent.com

00000246 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine Bug and Tar Remover 487g CODE: A6-000408

SECTION 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Identity……………………………………… Dry Shine Bug and Tar Remover 487g

Product Item Numbers……………………………. A6-000408

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CANUTEC: (613)-996-6666 collect.

Recommended Use………………………………… Bug and Tar Remover Spray.

Consumer Commodity…………………………….. Yes.

Hazard Ratings:

HMIS……………………………………………………. Health: 1 Fire: 2 Reactivity: 1.

NFPA Rating…………………………………………. Health: 1 Fire: 2 Reactivity: 1.

SECTION 02: HAZARDS IDENTIFICATION

Emergency Overview……………………………… Contents harmful . May catch fire. Container may explode if heated. Do not puncture. Do

not burn. Do not get in eyes or clothing. Do not breathe fumes. May cause skin and eye

irritation. KEEP OUT OF REACH OF CHILDREN .

Potential Health Effects:

Eye Contact…………………………………………… This product causes irritation, redness and pain.

Skin Contact …………………………………………. Can cause skin irritation. Prolonged or repeated contact may dry the skin.

Ingestion……………………………………………….. Ingestion may cause headache, nausea, vomiting and weakness.

Inhalation………………………………………………. Inhalation of solvents or dust may cause irritation.

SECTION 03: COMPOSITION/INFORMATION ON INGREDIENTS

HAZARDOUS INGREDIENTS CAS # WT. %

VM&P Naphtha 8032-32-4 10-30

Petroleum Distillates (Naphtha Hydrotreated Heavy) 64742-48-9 5-10

Isobutane 75-28-5 7-13

Propane 74-98-6 1-5

2-Butoxyethanol 111-76-2 1-5

Hydrotreated Light Petroleum Distillate 64742-47-8 1-5

2-Propanol 67-63-0 1-5

SECTION 04: FIRST AID MEASURES

Eye Contact…………………………………………… Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the

upper and lower eyelids. Get medical attention if irritation persists.

Skin Contact………………………………………….. Wash thoroughly with soap and lukewarm water. Remove contaminated clothing. Launder

clothing before reuse.

Ingestion……………………………………………….. If ingested, do not induce vomiting, get medical attention.

Inhalation………………………………………………. If inhaled, remove to fresh air. If not breathing, give artificial respiration and obtain

immediate medical assistance. If breathing is difficult, give oxygen and get medical

attention. Do not give adrenaline, epinephrine or similar drugs following exposure to this

product.

Additional Information……………………………… Note to the doctor; treat symptomatically.

SECTION 05: FIRE FIGHTING MEASURES

Flammability Class…………………………………. Flammable.

Extinguishing Media……………………………….. Use media suitable to the surrounding fire such as foam, dry chemical or water fog.

Sensitivity to Mechanical Impact………………. Not expected to be sensitive.

Sensitivity to Static Discharge………………….. Not expected to be sensitive.

SDS & Labels by TECIS www.trivalent.com

00000246 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine Bug and Tar Remover 487g CODE: A6-000408

SECTION 06: ACCIDENTAL RELEASE MEASURES

Spills and Leaks…………………………………….. Large spill or leak is unlikely in aerosol containers. If spill or leak occurs, ventilate enclosed

spaces and disperse gas with floor-level forced-air ventilation. Exhaust vapours outdoors.

Do not smoke or operate internal combustion engines. Remove all sources of ignition.

SECTION 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Use with adequate ventilation. Keep container tightly closed. Do not store in temperatures

above 120°F (50°C).

SECTION 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

INGREDIENTS TWA STEL PEL STEL REL

VM&P Naphtha Not established Not established Not established Not established Not established

Petroleum Distillates 300 ppm Not available 500 ppm (2,900 Not available Not available

(Naphtha Hydrotreated mg/m³)

Heavy)

Isobutane 800 ppm 1000 ppm 800ppm Not available 800 ppm (TWA)

Propane 2,500 ppm Not available 1,000 ppm Not available 1,000 ppm

2-Butoxyethanol 20 ppm Not available 50 ppm Not available Not available

Hydrotreated Light Not available Not available Not available Not available Not available

Petroleum Distillate

2-Propanol Not available Not available Not available Not available Not available

400 PPM

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Not normally required. Use rubber or latex gloves when there is a potential for prolonged or

excessive skin contact.

Respiratory Protection…………………………….. Use approved NIOSH respirators for emergencies.

Appropriate Engineering Controls…………….. Local exhaust ventilation required to maintain the point of use below the Threshold Limit

Value if unprotected personnel are involved.

Exposure Limits

SECTION 09: PHYSICAL AND CHEMICAL PROPERTIES

Physical State………………………………………… Aerosol.

Physical Appearance………………………………. Creamy white .

Odour…………………………………………………… Odourless.

Odour Threshold (ppm)…………………………… Not available.

pH………………………………………………………… 8.5 – 10.0.

Internal can pressure (psig)……………………… 30-40.

Vapour Density (Air=1)……………………………. Not available.

Evaporation Rate (n-Butyl Acetate = 1)……… < 1 (n-Butyl Acetate = 1).

Initial Boiling Point/Boiling Range (°C)………. Not available.

VOC Content…………………………………………. Not available.

Specific Gravity …………………………………….. 0.910-0.970.

Specific Gravity (Aerosol)………………………… 0.980-1.020 .

Solubility in water…………………………………… Soluble in water.

Aerosol Flame Projection………………………… No data.

Auto Ignition Temperature (Propellant), °C… 460°C (860°F).

Flashback……………………………………………… No data .

Flash Point (°C), Method…………………………. Closed cup: -83.15 ºC (-117.7 ºF).

Lower Flammable Limit (% Vol)……………….. 1.8.

Upper Flammable Limit (% Vol)……………….. 9.5.

SECTION 10: STABILITY AND REACTIVITY

Chemical Stability…………………………………… Stable at normal temperatures and pressures.

Incompatible Materials……………………………. Strong oxidizing agents.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge.

Hazardous Decomposition Products…………. May form carbon dioxide and carbon monoxide, various hydrocarbons.

Possibility of Hazardous Reactions…………… Will not occur.

SDS & Labels by TECIS www.trivalent.com

00000246 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine Bug and Tar Remover 487g CODE: A6-000408

SECTION 11: TOXICOLOGICAL INFORMATION

INGREDIENTS LC50 LD50

VM&P Naphtha 3400 ppm (4 hrs – rat) 5000 mg/kg (rat – oral); 3160

mg/kg (rabbit – dermal)

Petroleum Distillates (Naphtha Hydrotreated Heavy) 8500 mg/m3 (Rat,4hr) 5000 ppm (Oral,Rat)

Isobutane 658 mg/L (4hrs,rat) Not available

Propane >800,000 ppm (15 min,Rat) Not available

2-Butoxyethanol 450 ppm (4hr,rat) 470 mg/kg (4hr,oral,rat)

Hydrotreated Light Petroleum Distillate 5.500 mg/L (rat- Inhl) 5.0 g/kg (rat – oral); 4.0 g/kg

(rabbit – dermal)

2-Propanol Not available Not available

Route of Exposure………………………………….. Eye contact, Skin contact, Skin absorption, Inhalation, and Ingestion.

Effects of Acute Exposure……………………….. This product is harmful if inhaled or swallowed. Contact with skin and eyes may cause mild

to moderate irritation and frostbite. Symptoms may include redness, pain, numbness,

prickling and itching. Inhalation of vapours causes irritation to the nose, throat and

respiratory tract, with coughing, wheezing, dizziness, headache, drowsiness, nausea and

vomiting. Inhalation of higher concentrations may result in central nervous system

depression and unconsciousness. High vapour concentrations reduce oxygen available for

breathing, resulting in asphyxiation.

Chronic Effects………………………………………. May cause skin defatting and dermatitis. Intentional misuse by deliberately concentrating

and inhaling this product may be harmful or fatal.

Carcinogenicity………………………………………. None known when used below acute toxicity limit.

Reproductive Toxicity……………………………… No information is available, and no adverse effects are expected.

Teratogenicity………………………………………… No information is available, and no adverse effects are expected.

Germ Cell Mutagenicity…………………………… No information is available, and no adverse effects are expected.

Toxicological Data

SECTION 12: ECOLOGICAL INFORMATION

Environmental……………………………………….. Liquid release is only expected to cause localized, non-persistent environmental damage,

such as freezing.

SECTION 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. Dispose in accordance with local, provincial and federal regulations.

SECTION 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.1, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.1, UN1950, LTD QTY, Consumer commodity ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.1, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.1, UN1950, LTD QTY.

SECTION 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas. B5: Flammable Aerosol. D2B: Material causing

other toxic Materials.

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. OSHA (29CFR 1910.1200) Classification: Compressed Gas. HIMS

Classifications: see section 01.

SECTION 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. Empack assumes no responsibility for personal injury or property damage to

vendees or users or third parties, caused by the material. Such vendees or users assume

all risks with the use of the material. This product has been classified in accordance with

the hazard criteria of the CPR and the SDS contains all the information required by the

CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

SDS & Labels by TECIS www.trivalent.com

00000246 SAFETY DATA SHEET Page 4

PRODUCT: Dry Shine Bug and Tar Remover 487g CODE: A6-000408

SECTION 16: OTHER INFORMATION

Abbreviations…………………………………………. Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information STOT: System.Specific Target Organ Toxicity.

Prepared by ………………………………………….. Regulatory Affairs

 

Preparation Date……………………………………. NOV 16/2015

MSDS Dry Shine Salt Eraser

00000485 SAFETY DATA SHEET Page 1

Orapi Canada

7521 boul. Henri-Bourassa Est

Montreal, Quebec, H1E-1N9

Canada

Tel: 514-735-3272

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 01: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Item Numbers……………………………. A6-000008

Product Identity……………………………………… Dry Shine – 487g

Manufacturer…………………………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

24 hour emergency telephone number……… CHEM TREC: 800-424-9300.

Recommended Use………………………………… Waterless wash and wax.

Chemical Family…………………………………….. Mixture.

Section 02: HAZARDS IDENTIFICATION

Hazard Classification:

Physical Hazards……………………………………. Gases Under Pressure – Compressed gas . Flammable Aerosols – Category 1 .

Health Hazards………………………………………. Not Classified.

Environmental Hazards…………………………… Not Classified.

Label Elements:

Signal Word…………………………………………… DANGER.

Hazard Statement………………………………….. Extremely flammable aerosol. Pressurized container: may burst if heated.

Precautionary Statements:

Prevention…………………………………………….. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No

smoking. Do not spray on an open flame or other ignition source . Do not pierce or burn,

even after use.

Response……………………………………………… Not applicable.

Storage…………………………………………………. Protect from sunlight. Do not expose to temperatures exceeding 50°C /122°F . Store in a

well ventilated place .

Disposal………………………………………………… Not applicable.

Hazard(s) not otherwise classified (HNOC).. None Known.

Section 03: COMPOSITION/INFORMATION ON INGREDIENTS

Hazardous Ingredients CAS # Wt. %

Isobutane 75-28-5 10-30

Hydrotreated Light Petroleum Distillate 64742-47-8 5-10

Propane 74-98-6 1-5

Section 04: FIRST AID MEASURES

Inhalation………………………………………………. If inhaled, remove to fresh air. If not breathing, give artificial respiration and obtain

immediate medical assistance.

Skin Contact………………………………………….. Wash exposed area with soap and water. Remove contaminated clothing. If irritation or

redness develops, seek medical attention.

Eye Contact…………………………………………… Check for and remove contact lenses. Immediately flush eyes with water for a minimum of

15 minutes keeping eyelids open. Consult a doctor if any irritation occurs.

Ingestion……………………………………………….. Ingestion is not a likely route of exposure. If ingested, do not induce vomiting, get medical

attention.

Most important symptoms/effects, acute and Immediate medical attention is required.

delayed

Indication of immediate medical attention and Provide general supportive measures and treat symptomatically. In case of shortness of

special treatment needed breath give oxygen. Keep victim warm. Keep victim under observation. Symptoms may be

delayed.

00000485 SAFETY DATA SHEET Page 2

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 05: FIRE FIGHTING MEASURES

Suitable Extinguishing Media…………………… Dry chemical powder. Carbon dioxide. Foam, water spray or fog.

Unsuitable Extinguishing Media……………….. Do not use water jet as an extinguisher, as this will spread the fire.

Specific Hazards Arising from the Chemical. Contents under pressure. Pressurized container may explode when exposed to heat or

flame.

Special Protective Equipment and …………… Firefighters must use standard protective equipment including flame retardant coat, helmet

Precautions for Firefighters with water to prevent vapor pressure build up. For massive fire in cargo area, use

unmanned hose holder or monitor nozzles, if possible. If not, withdraw and let fire burn out.

General Fire Hazards……………………………… Flammable Aerosol.

Section 06: ACCIDENTAL RELEASE MEASURES

Personal Precautions, Protective Equipment No action shall be taken involving any personal risk or without suitable training. Evacuate

and Emergency Procedures surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not

touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate

ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate

personal protective equipment (see Section 08).

Methods and Materials for Containment and Spill areas may be slippery. Use care to avoid falls or other accidents . Contain the spill.

Cleaning Up Clean up the spill area with detergent and water. Once spilled material has been collected,

use rags or other suitable material to clean spill area. Rags should be properly disposed of.

Environmental Precautions……………………… Keep out of drains, sewers, ditches, and waterways. Minimize use of water to prevent

environmental contamination.

Section 07: HANDLING AND STORAGE

Precautions for Safe Handling………………….. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is

missing or defective. Do not spray on a naked flame or any other incandescent material.

Do not pressurize, cut, weld, braze, solder, drill, grind, or expose empty containers to heat,

sparks or open flames. Avoid contact with eyes, skin, and clothing. Avoid breathing vapour

of this product. Avoid contact with skin and eyes. Avoid prolonged exposure. Use in

well-ventilated areas.

Conditions for Safe Storage including any … Store locked up . Pressurized container. Protect from sunlight and do not expose to

Incompatibilities temperatures exceeding 50°C (122°F). Do not puncture, incinerate or crush. Do not handle

or store near an open flame, heat or other sources of ignition. Store away from

incompatible materials (see Section 10).

Section 08: EXPOSURE CONTROLS / PERSONAL PROTECTION

ACGIH TLV OSHA PEL NIOSH

Ingredients TWA STEL PEL STEL REL

Isobutane 800 ppm 1000 ppm 800 ppm Not available 800 ppm (TWA)

Hydrotreated Light Not available Not available Not available Not available Not available

Petroleum Distillate

Propane 2,500 ppm Not available 1,000 ppm Not available 1,000 ppm

Appropriate Engineering Controls…………….. Local exhaust ventilation required to maintain the point of use below the Threshold Limit

Value if unprotected personnel are involved.

Individual Protection Measures:

Eye/Face Protection……………………………….. Do not get in eyes. Wear safety glasses with side-shields.

Skin Protection………………………………………. Chemical resistant gloves are recommended. Avoid contact with the skin. Wear

appropriate chemical resistant clothing.

Respiratory Protection…………………………….. Use dust and mist respirator.

Thermal Hazards……………………………………. None Known.

General Hygiene Considerations……………… When using, do not eat, drink or smoke. Always observe good personal hygiene measures,

such as washing after handling the material and before eating, drinking, and/or smoking.

Routinely wash work clothing and protective equipment to remove contaminants.

Section 09: PHYSICAL AND CHEMICAL PROPERTIES

Form…………………………………………………….. Aerosol.

Physical Appearance………………………………. Milky straw.

Odor…………………………………………………….. Fragrance.

Odor Threshold (ppm)…………………………….. N/A.

Specific Gravity (Aerosol)………………………… 0.910-0.970.

Specific Gravity (Liquid)………………………….. 0.980-1.020.

Aerosol Vapour Pressure (psig, 21°C)………. 40-50.

Vapour Density (Air=1)……………………………. > 1.

pH………………………………………………………… 7.0-9.0.

Boiling Point liquid (°C)……………………………. -11.72°C (10.9°F). (For propellant).

Melting/Freezing Point (°C)……………………… N/A.

Flash Point (°C), Method…………………………. Closed cup: -83.15 ºC (-117.7 ºF). (For propellant).

00000485 SAFETY DATA SHEET Page 3

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 09: PHYSICAL AND CHEMICAL PROPERTIES

Flashback……………………………………………… No.

Evaporation Rate (n-Butyl Acetate = 1)

VOC Content…………………………………………. N/A.

Solubility in water…………………………………… Completely.

Aerosol Flame Projection………………………… No data.

Auto Ignition Temperature (°C)…………………. 460°C (860°F). (For propellant).

Lower Flammable Limit (% Vol)……………….. 1.8. (For propellant).

Upper Flammable Limit (% Vol)……………….. 9.5. (For propellant).

Coefficient of Water/Oil Distribution………….. N/A.

Viscosity……………………………………………….. N/A.

Section 10: STABILITY AND REACTIVITY

Reactivity ……………………………………………… Product not reactive under normal conditions of use.

Chemical Stability…………………………………… Material is stable under normal conditions.

Possibility of Hazardous Reactions…………… Will not occur.

Conditions to Avoid………………………………… Avoid sources of heat and flame, and electrostatic charge. Contact with incompatible

substances.

Incompatible Materials……………………………. Strong oxidizing agents. Strong acids. Strong bases.

Hazardous Decomposition Products…………. Carbon Monoxide, Carbon Dioxide, Phosgene, Hydrogen Chloride Gas.

Section 11: TOXICOLOGICAL INFORMATION

Ingredients LC50 LD50

Isobutane 658 mg/L (4hrs,Rat) Not available

Hydrotreated Light Petroleum Distillate 5.500 mg/L (rat- Inhl) 5.0 g/kg (rat – oral); 4.0 g/kg (rabbit – dermal)

Propane >800,000 ppm (15 min,Rat) Not available

Information on Likely Routes of Exposure:

Routes of entry – Inhalation……………………… Yes.

Routes of entry – Skin & Eye……………………. Yes.

Routes of entry – Ingestion………………………. No.

Routes of entry – Skin Absorption……………… No.

Symptoms Related to the Physical, Chemical

and Toxicological Characteristics

Acute Toxicity………………………………………… No known significant effects.

Skin Corrosion/Irritation…………………………… Causes mild skin irritation. Prolonged contact may be more irritating.

Serious Eye Damage/Eye Irritation…………… May irritate eyes.

Respiratory or Skin Sensitization……………… Inhalation may cause respiratory tract irritation.

Germ Cell Mutagenicity…………………………… No data available to indicate product or any components present at greater than 0.1% are

mutagenic.

Carcinogenicity………………………………………. No information is available.

Reproductive Toxicity……………………………… Based on available data, the classification criteria are not met.

Specific Target Organ Toxicity – Single …….. No data available .

Exposure

Specific Target Organ Toxicity – Repeated .. No known significant effects.

Exposure

Aspiration Hazard

Chronic Effects………………………………………. Repeated or prolonged skin exposure may result in moderate irritation, drying, cracking

and defatting of the skin (dermatitis).

Section 12: ECOLOGICAL INFORMATION

Ecotoxicity…………………………………………….. May be dangerous for the environment. No data is available on the product itself. Should

not be released into the environment.

Persistence and degradability …………………. The product itself has not been tested.

Bioaccumulation Potential……………………….. The product itself has not been tested.

Mobility in Soil……………………………………….. The product itself has not been tested.

Other Adverse Effects…………………………….. None Known.

Section 13: DISPOSAL CONSIDERATIONS

Appropriate Disposal Methods…………………. This material and its container must be disposed of as hazardous waste. Avoid release to

the environment. Spilled material and water rinses are classified as chemical waste and

must be disposed of in accordance with current local, provincial and federal regulations.

Contents under pressure. Do not puncture, incinerate or expose to heat, even when empty.

00000485 SAFETY DATA SHEET Page 4

PRODUCT: Dry Shine – 487g CODE: A6-000008

Section 14: TRANSPORT INFORMATION

TDG (Canada- Road)……………………………… AEROSOLS, Class 2.1, UN1950.

DOT (US-Road)……………………………………… AEROSOLS, Class 2.1, UN1950, LTD. QTY. OR ORM-D.

IMDG (International- Marine)……………………. AEROSOLS, Class 2.1, UN1950.

IATA (International- Air)…………………………… AEROSOLS, Class 2.1, UN1950, LTD QTY.

Section 15: REGULATORY INFORMATION

Canada Regulations:………………………………. WHMIS Classification. A: Compressed gas. B5: Flammable Aerosol.

Canadian Environmental Protection Act ……. All ingredients listed appear on the Domestic Substances List (DSL).

(CEPA)

US Regulations……………………………………… Environmental Protection Act: Constituents of this product are included on the TSCA

inventory. This product is considered hazardous under the OSHA Hazard Communication

Standard.

Section 16: OTHER INFORMATION

Disclaimer……………………………………………… The information contained herin is based on data considered accurate. No warranty is

expressed or implied regarding the accuracy of this data or the results obtained from the

use thereof. The SDS provider assumes no responsibility for personal injury or property

damage to vendees or users or third parties, caused by the material. Such vendees or

users assume all risks with the use of the material. This product has been classified in

accordance with the hazard criteria of the CPR and the SDS contains all the information

required by the CPR. THIS SDS IS VALID FOR THREE YEARS.

Abbreviations…………………………………………. ACGIH: American Conference of Governmental Industrial Hygienists; CAS: Chemical

Abstract Service; NIOSH: National Institute for Occupational Safety and Health, OSHA:

Occupational Safety and Health Administration- USA; TSCA: Toxic Substances Control Act

1976-USA; PEL: Permissible Exposure Limit; REL: Recommended Exposure Limit; TLV:

Threshold Limit Value; VOC: Volatile Organic Content; WHIMIS: Workplace Hazardous

Materials Information System.

Prepared by ………………………………………….. Regulatory Affairs

 

Preparation Date……………………………………. Mar05/15

MSDS Dry Shine Motorcyle Shine and Protection

Powered by www.trivalent.com

00000710 FICHES DE DONNÉES DE SÉCURITÉ Page 1

Lubco

1963, rue Frank-Carrel, Suite 102

Quebec, QC, G1N 2E6

Canada

(418) 665-2920

PRODUIT: Lubco Motorbike Shine & Protection – 200g CODE: A6-000600-USA

SECTION 01: IDENTIFICATION DU PRODUIT CHIMIQUE ET DE L’ENTREPRISE

Numéro del produit…………………………………. A6-000600-USA

Identité du produit…………………………………… Lubco Motorbike Shine & Protection – 200g

Référence du fabricant……………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

Numéro de téléphone d’urgence 24 heures.. CHEM TREC : 800-424-9300.

Utilisation recommandée…………………………. Polir et protéger les surfaces.

Famille chimique……………………………………. Mélange.

SECTION 02: IDENTIFICATION DES DANGERS

Classification des dangers :

Dangers physiques…………………………………. Aérosols – catégorie 3. Gaz sous pression – gaz liquéfié .

Dangers pour la santé…………………………….. Irritation de la peau – catégorie 3. Toxicité pour certains organes cibles précis, exposition

unique – catégorie 3.

Dangers pour l’environnement…………………. Non classifié.

Éléments d’étiquetage :

Mot indicateur………………………………………… MISE EN GARDE.

Mention de danger…………………………………. Récipient sous pression : risquent d’éclater si chauffé. Contient un gaz sous pression ; peut

exploser s’il est chauffé. Provoque une irritation cutanée bénigne. Peut provoquer

somnolence ou vertiges.

Conseils de prudence :

Prévention…………………………………………….. Tenir à l’écart de chaleur, des surfaces chaudes, étincelles, flammes nues et autres

sources d’ignition. Non fumeur. Ne pas percer ou brûler, même après l’utilisation. Laver

soigneusement les mains après la manipulation. Éviter de respirer les

poussières/fumées/gaz/brouillards/vapeurs/aérosols. Utiliser uniquement à l’extérieur ou

dans un endroit bien aéré.

Réponse……………………………………………….. Si se produit une irritation cutanée ou une éruption cutanée : consulter un

médecin/conseils. CAS d’inhalation : Supprimer la personne à l’air frais et garder

confortable pour acquerir. Appeler un centre antipoison, si vous vous sentez mal.

Stockage………………………………………………. Protéger des rayons du soleil. Ne pas exposer à des températures supérieures à 50°

C/122° F. Stocker dans un endroit bien ventilé . Magasin fermé à clé.

Élimination…………………………………………….. Ne s’applique pas.

Danger (s) non classé (HNOC)………………… Aucune n’est connue.

SECTION 03: INFORMATION SUR LES COMPOSANTS

INGRÉDIENTS DANGEREUX # CAS Wt. %

Naphta (pétrole), traités hydro lumière 64742-49-0 10-30

Isobutane 75-28-5 7-13

Agents tensio-actifs Mix. 7-13

Essence mineral inodore 64741-65-7 3-7

Distillats de pétrole 64742-47-8 1-5

Propane 74-98-6 1-5

Powered by www.trivalent.com

00000710 FICHES DE DONNÉES DE SÉCURITÉ Page 2

PRODUIT: Lubco Motorbike Shine & Protection – 200g CODE: A6-000600-USA

SECTION 04: DESCRIPTION DES PREMIERS SOINS À PORTER EN CAS D’URGENCE

Inhalation………………………………………………. S’il est inhalé, enlever à l’air frais. Si ce n’est pas respirer, pratiquer la respiration artificielle

et obtenir une assistance médicale immédiate.

Contact avec la peau………………………………. Laver la surface exposée à l’eau savonneuse. Enlever les vêtements contaminés. Si une

irritation ou une rougeur se développe, consulter un médecin.

Contact avec les yeux…………………………….. Vérifier et enlever les lentilles de contact. Rincer immédiatement les yeux avec de l’eau

pendant au moins 15 minutes, garder les paupières ouvertes. Consulter un médecin en

cas de toute irritation.

Ingestion……………………………………………….. Ingestion n’est pas une voie probable de l’exposition. En cas d’ingestion, ne pas faire

vomir, consulter un médecin.

Symptômes/effets plus importants, aigus et . Une attention médicale immédiate est nécessaire.

retardés

Indication des soins médicaux immédiats et Fournir des mesures générales de soutien et le traiter selon les symptômes. Donner de

traitement spécial nécessaire l’oxygène en cas d’essoufflement. Réchauffer la victime. Garder la victime sous

observation. Les symptômes peuvent être retardés.

SECTION 05: MESURES DE LUTTE CONTRE L’INCENDIE

D’extinction approprié……………………………… Poudre chimique sèche. Dioxyde de carbone. Mousse, eau pulvérisée ou en brouillard.

D’extinction inappropriés…………………………. Ne pas utiliser de jet d’eau comme un extincteur, comme cela se propagera le feu.

Dangers particuliers découlant de la ………… Contenu sous pression. Contenants sous pression pouvant exploser lorsqu’ils sont

substance chimique exposés à la chaleur ou de flamme.

Équipement spécial de protection et ………… Pompiers doivent utiliser un équipement de protection standard y compris manteau

précautions pour les pompiers ignifuge, casque avec l’eau pour éviter l’accumulation de pression de vapeur vers le haut.

Pour énorme incendie dans le compartiment, utiliser le support à boyau sans pilote ou

moniteur buses, si possible. Si ce n’est pas le cas, retirer et laisser le feu brûler.

SECTION 06: MESURES À PRENDRE EN CAS DE DISPERSION ACCIDENTELLE

Précautions individuelles, équipements de .. Aucun prend les mesures impliquant des risques personnels ou sans formation adéquate.

protection et procédures d’urgence Évacuer les régions avoisinantes. Empêchent le personnel inutile et non protégé de

pénétrer. Évitez de marcher à travers le produit déversé. Éviter de respirer les vapeurs ou

brouillards. Prévoyez une ventilation adéquate. Porter un respirateur approprié lorsque la

ventilation est inadéquate. Mettre sur les équipements de protection individuelle approprié

(voir Section 08).

Méthodes et matériaux de confinement et de Zones de déversement peuvent être glissants. Faire attention à éviter les chutes ou autres

nettoyage accidents . Contenir le déversement. Nettoyer la zone de déversement à l’eau et de

détergent. Une fois que le produit déversé a été recueilli, utiliser chiffons ou autre matériau

approprié pour déversement propre zone. Chiffons doivent être correctement éliminés.

Précautions environnementales……………….. Garder hors de drains, égouts, fossés et cours d’eau. Minimisez l’utilisation de l’eau pour

éviter la contamination de l’environnement.

SECTION 07: PRÉCAUTIONS DE STOCKAGE, DE L’EMPLOI ET DE MANIPULATION

Précautions pour la manipulation……………… Récipient sous pression : ne pas percer ou brûler, même après utilisation. Ne pas utiliser si

le bouton du spray est manquant ou défectueux. Ne pas vaporiser sur une flamme nue ou

tout autre matériau incandescent. Ne pas pressuriser, couper, souder, braser, souder,

percer, moudre ou exposer des conteneurs vides pour la chaleur, d’étincelles ou de

flammes nues. Éviter tout contact avec les yeux, la peau et vêtements. Éviter de respirer

les vapeurs de ce produit. Éviter tout contact avec la peau et les yeux. Éviter une

exposition prolongée. Utiliser dans des endroits bien aérés.

Conditions d’entreposage sécuritaire, y ……. Magasin fermé à clé. Récipient sous pression. Protéger des rayons du soleil et ne pas

compris les incompatibilités exposer à des températures supérieures à 50° C (122° F). Ne pas percer, incinérer ou

écraser. Ne pas manipuler ou entreposer près d’une flamme, de chaleur ou d’autres

sources d’ignition. Magasin loin des matières incompatibles (voir Section 10).

SECTION 08: MESURES DE PROTECTION CONTRE L`EXPOSITION / PROTECTION INDIVIDUELLE

ACGIH TLV OSHA PEL NIOSH

INGRÉDIENTS TWA STEL PEL STEL REL

Naphta (pétrole), traités 353 ppm Non Disponible Non Disponible Non Disponible Non Disponible

hydro lumière

Isobutane 800 ppm 100 ppm 800 ppm Non disponible 800 ppm

Agents tensio-actifs Non disponible Non disponible Non disponible Non disponible Non disponible

Essence mineral inodore Non disponsible Non disponsible Non disponsible Non disponsible Non disponsible

Distillats de pétrole 200 mg/m3 Non disponsible 5 mg/m3 Non disponsible Non disponsible

Propane 2,500 ppm Non disponible 1,000 ppm Non disponible 1,000 ppm

Powered by www.trivalent.com

00000710 FICHES DE DONNÉES DE SÉCURITÉ Page 3

PRODUIT: Lubco Motorbike Shine & Protection – 200g CODE: A6-000600-USA

SECTION 08: MESURES DE PROTECTION CONTRE L`EXPOSITION / PROTECTION INDIVIDUELLE

Contrôles d’ingénierie appropriés……………… L’évacuation par une ventilation locale est nécessaire pour maintenir le point d’utilisation

ci-dessous sous la Valeur du Seuil de Limite si le personnel n’est pas protégé.

Mesures de Protection individuelle :

Protection des yeux/visage……………………… Ne recevez pas dans les yeux. Porter des lunettes de sécurité avec écrans latéraux.

Protection de la peau……………………………… Des gants jetables sont recommandés. Éviter tout contact avec la peau. Porter des

vêtements appropriés résistants aux produits chimiques.

Protection des voies respiratoires…………….. Respirateur de poussière et de la brume d’utilisation.

Risques thermiques………………………………… Aucune n’est connue.

Considérations d’hygiène générale…………… Lors de l’utilisation, pas manger, boire ou fumer. Respectez toujours les mesures d’hygiène

personnelle, tels que lavage après avoir manipulé le matériel et avant de manger, boire ou

fumer. Régulièrement laver les vêtements de travail et équipements de protection avant

d’utiliser.

SECTION 09: PROPRIÉTÉS PHYSICO-CHIMIQUES

Formulaire…………………………………………….. Aérosol.

Apparence physique……………………………….. Blanc. Beige.

Odeur…………………………………………………… Parfum.

Seuil de l’odeur (ppm)…………………………….. N/A.

Gravité spécifique (aérosol)…………………….. 0,842.

Densité (liquide)…………………………………….. 0,928.

Pression de vapeur des aérosols (lb/po2, 21° 40-50.

C)

Densité de vapeur (Air = 1)……………………… > 1.

pH………………………………………………………… Ne s’applique pas.

Liquide de Point d’ébullition (° C)………………. -11.72 ° C (10,9 ° F). (Pour le gaz propulseur).

Point de fusion/congélation (° C)………………. N/A.

Point d’éclair (° C), méthode…………………….. Coupe fermée :-83.15 ° c (-117.7 ° f). (Pour le gaz propulseur).

Retour de flamme…………………………………… Non.

Taux d’évaporation (acétate de n-butyle = 1) Non disponible.

Teneur en COV……………………………………… N/A.

Solubilité dans l’eau………………………………… Complètement.

Projection de flamme aérosol…………………… Aucune donnée.

Température d’auto-inflammation (° C)……… 460° C (860° F). (propergol).

Limite inférieur d’inflammabilité (% vol.)…….. 1.8. (propergol).

Limite supérieure d’inflammabilité (% vol.)…. 9.5. (propergol).

Coefficient de répartition eau/huile……………. N/A.

Viscosité……………………………………………….. N/A.

SECTION 10: STABILITÉ DU PRODUIT ET RÉACTIVITÉ

Réactivité ……………………………………………… Produit non réactif dans des conditions normales d’utilisation.

Stabilité chimique…………………………………… Matériau est stable dans des conditions normales.

Possibilité de réactions dangereuses………… Ne se produit pas.

Conditions à éviter………………………………….. Évitez les sources de chaleur et la flamme et la charge électrostatique. Entrer en contact

avec des substances incompatibles.

Matières incompatibles……………………………. Agents oxydants forts. Acides forts. Bases fortes.

Produits de décomposition dangereux ……… Monoxyde de carbone, le dioxyde de carbone, le phosgène, gaz de chlorure d’hydrogène.

Products

SECTION 11: INFORMATION TOXICOLOGIQUE

INGRÉDIENTS LC50 LD50

Naphta (pétrole), traités hydro lumière >20 mg/L (Rat,4hrs) >5000 mg/kg (Oral,Rat); >3000

mg/kg (Skin,Rabbit)

Isobutane 658 mg/L (4hrs,Rat) Non disponible

Agents tensio-actifs Non disponible Non disponible

Essence mineral inodore >5900 mg/m3 (rat-4hrs) >8000 ml/kg (rat -oral)

Distillats de pétrole >5 mg/l (4hrs – rat) >5,000 mg/kg (rat – Oral); >2,000

mg/kg (rabbit – Dermal)

Propane >800,000 ppm (15 min – rat) Non disponible

Informations sur les Routes probables

d’exposition :

Voies de pénétration – Inhalation………………. Oui.

Voies de pénétration – Skin & yeux…………… Oui.

Voies de pénétration – Ingestion……………….. Non.

Powered by www.trivalent.com

00000710 FICHES DE DONNÉES DE SÉCURITÉ Page 4

PRODUIT: Lubco Motorbike Shine & Protection – 200g CODE: A6-000600-USA

SECTION 11: INFORMATION TOXICOLOGIQUE

Voies de pénétration – Absorption par la peau Non.

Symptômes liés aux caractéristiques

physiques, chimiques et toxicologiques

Toxicité aiguë………………………………………… Pas d’effets significatifs connus.

Corrosion/Irritation cutanée……………………… Provoque une irritation cutanée bénigne. Le contact prolongé peut être plus irritant.

Irritation oculaire/dommages oculaires graves Peut irriter les yeux.

Sensibilisation respiratoire ou cutanée………. L’inhalation peut provoquer une irritation des voies respiratoires.

Mutagénicité sur les cellules germinales……. Aucune donnée disponible pour indiquer les produits ou les composants présents à plus de

0,1 % sont mutagènes.

Cancérogénicité…………………………………….. Aucune information n’est disponible.

Toxicité pour la reproduction……………………. Selon les données disponibles, les critères de classification ne sont pas remplies.

STOT – exposition unique………………………… Organes cibles toxicité unique exposition catégorie 3. Peut provoquer somnolence et

vertiges.

STOT – exposition répétée………………………. Pas d’effets significatifs connus.

Danger par aspiration

Effets chroniques……………………………………. Exposition répétée ou prolongée de la peau peut entraîner une irritation modérée,

séchage, fissuration et dessèchements de la peau (dermatite).

SECTION 12: RENSEIGNEMENTS ÉCOTOXICOLOGIQUES

Écotoxicité…………………………………………….. Peut être dangereux pour l’environnement. Il n’existe aucune donnée sur le produit

lui-même. Ne devraient pas être rejetées dans l’environnement. Naphta de pétrole (CAS #:

64742-49-0): toxicité pour les poissons : CL50 1,0 mg/L, 48 heures ; Toxicité pour les

autres invertébrés aquatiques : L50 3,87 mg/L, 48 heures ; Toxicité pour les algues : EC50

55 mg/L, en 48 h.

Persistance et dégradabilité ……………………. Le produit lui-même n’a pas été testé.

Potentiel de bioaccumulation…………………… Le produit lui-même n’a pas été testé.

Mobilité dans le sol…………………………………. Le produit lui-même n’a pas été testé.

Autres effets nocifs…………………………………. Aucune n’est connue.

SECTION 13: INFORMATIONS SUR L’ÉLIMINATION DES DÉCHETS

Méthodes d’élimination appropriées………….. Ce produit et son récipient doivent être éliminés comme déchet dangereux. Éviter le rejet

dans l’environnement. Les rinçages et de l’eau déversées sont classés comme déchets

chimiques et doivent être éliminés conformément aux règlements les, provinces et

fédéraux. Contenu sous pression. Ne pas percer, incinérer ou exposer à la chaleur, même

lorsqu’il est vide.

SECTION 14: INFORMATION RELATIVES AU TRANSPORT

TMD (Canada – Road)…………………………….. AÉROSOLS, classe 2.1, UN1950.

DOT (U.S. route)……………………………………. AÉROSOLS, classe 2.1, UN1950, LTD QTY, bien de consommation ORM-D.

IMDG (International – Marine)…………………… AÉROSOLS, classe 2.1, UN1950.

IATA (International Air)……………………………. AÉROSOLS, classe 2.1, UN1950, LTD QTY.

SECTION 15: INFORMATION RÉGLEMENTAIRES

Règlements de Canada :…………………………. Classification du SIMDUT. A: gaz comprimé. D2B : Matières causant d’autres matériaux

toxiques.

Loi sur la Protection de l’environnement …… Tous les ingrédients figurent sur la liste intérieure des Substances (LIS).

canadien (LCPE)

Règlements américains…………………………… Loi sur la Protection environnementale : Les constituants de ce produit figurent sur

l’inventaire du TSCA. Ce produit est considéré comme dangereux par l’OSHA Hazard

Communication Standard.

SECTION 16: AUTRES RENSEIGNEMENTS

Clause de non-responsabilité…………………… Les informations contenues dans ce document sont issues des données considérées

comme exactes. Aucune garantie ou garantie expresse ou implicite quant à l’exactitude de

ces données ou les résultats obtenus par l’utilisation de celui-ci. Le fournisseur de SDS

n’assume aucune responsabilité pour les dommages corporels ou matériels personnels à

des fournisseurs ou des utilisateurs ou des tiers, causés par le matériel. Ces fournisseurs

ou utilisateurs assumeront tous les risques avec l’utilisation du matériel. Ce produit a été

classé selon les critères de danger du RPC et de la FDS contient tous les renseignements

exigés par le RPC. .

Abréviations…………………………………………… ACGIH : American Conference of Governmental Industrial Hygienists ; CAS: Chemical

Abstract Service ; NIOSH : National Institute for Occupational Safety and Health, OSHA :

Powered by www.trivalent.com

00000710 FICHES DE DONNÉES DE SÉCURITÉ Page 5

PRODUIT: Lubco Motorbike Shine & Protection – 200g CODE: A6-000600-USA

SECTION 16: AUTRES RENSEIGNEMENTS

Abréviations…………………………………………… Occupational Safety and Health Administration – États-Unis ; TSCA : Toxic Substances

contrôlent Act 1976-USA ; PEL : Limite d’exposition permise ; REL : Recommandé limite

d’exposition ; VLE : Valeur limite ; COV : Teneur organique Volatile ; SIMDUT : Système

d’Information au travail matières dangereuses STOT : toxicité pour certains organes cibles.

Préparé par ………………………………………….. Affairs Regulatory

Version Révisée ……………………………………. JAN 27/2017

MSDS Dry Shine Motorcyle Insect and Tar

Powered by www.trivalent.com

00000711 FICHES DE DONNÉES DE SÉCURITÉ Page 1

Lubco

1963, rue Frank-Carrel, Suite 102

Quebec, QC, G1N 2E6

Canada

(418) 665-2920

PRODUIT: Lubco Motorbike Insect & Tar Remover – 200 g CODE: A6-000601-USA

SECTION 01: IDENTIFICATION DU PRODUIT CHIMIQUE ET DE L’ENTREPRISE

Numéro del produit…………………………………. A6-000601-USA

Identité du produit…………………………………… Lubco Motorbike Insect & Tar Remover – 200 g

Référence du fabricant……………………………. Empack Spraytech Inc.

98 Walker Drive

Brampton

Ontario

Canada

L6T 4H6

905-792-6571

Numéro de téléphone d’urgence 24 heures.. CHEM TREC : 800-424-9300.

Utilisation recommandée…………………………. Suppression de bugs, de goudron et de crasse.

Famille chimique……………………………………. Mélange.

SECTION 02: IDENTIFICATION DES DANGERS

Classification des dangers :

Dangers physiques…………………………………. Aérosols – catégorie 3. Gaz sous pression – gaz liquéfié .

Dangers pour la santé…………………………….. Irritation de la peau – catégorie 3. Toxicité pour certains organes cibles précis, exposition

unique – catégorie 3.

Dangers pour l’environnement…………………. Non classifié.

Éléments d’étiquetage :

Mot indicateur………………………………………… MISE EN GARDE.

Mention de danger…………………………………. Récipient sous pression : risquent d’éclater si chauffé. Contient un gaz sous pression ; peut

exploser s’il est chauffé. Provoque une irritation cutanée bénigne. Peut provoquer

somnolence ou vertiges.

Conseils de prudence :

Prévention…………………………………………….. Tenir à l’écart de chaleur, des surfaces chaudes, étincelles, flammes nues et autres

sources d’ignition. Non fumeur. Ne pas percer ou brûler, même après l’utilisation. Laver

soigneusement les mains après la manipulation. Éviter de respirer les

poussières/fumées/gaz/brouillards/vapeurs/aérosols. Utiliser uniquement à l’extérieur ou

dans un endroit bien aéré.

Réponse……………………………………………….. Si se produit une irritation cutanée ou une éruption cutanée : consulter un

médecin/conseils. CAS d’inhalation : Supprimer la personne à l’air frais et garder

confortable pour acquerir. Appeler un centre antipoison, si vous vous sentez mal.

Stockage………………………………………………. Protéger des rayons du soleil. Ne pas exposer à des températures supérieures à 50°

C/122° F. Stocker dans un endroit bien ventilé . Magasin fermé à clé.

Élimination…………………………………………….. Ne s’applique pas.

Danger (s) non classé (HNOC)………………… Aucune n’est connue.

SECTION 03: INFORMATION SUR LES COMPOSANTS

INGRÉDIENTS DANGEREUX # CAS Wt. %

Naphta (pétrole), traités hydro lumière 64742-49-0 10-30

Isobutane 75-28-5 7-13

Essence mineral inodore 64741-65-7 3-7

Propane 74-98-6 1-5

Alcool Isopropyle 67-63-0 1-5

2-Butoxyéthanol 111-76-2 1-5

Distillats de pétrole 64742-47-8 1-5

Agents tensio-actifs Mix. 1-5

Powered by www.trivalent.com

00000711 FICHES DE DONNÉES DE SÉCURITÉ Page 2

PRODUIT: Lubco Motorbike Insect & Tar Remover – 200 g CODE: A6-000601-USA

SECTION 04: DESCRIPTION DES PREMIERS SOINS À PORTER EN CAS D’URGENCE

Inhalation………………………………………………. S’il est inhalé, enlever à l’air frais. Si ce n’est pas respirer, pratiquer la respiration artificielle

et obtenir une assistance médicale immédiate.

Contact avec la peau………………………………. Laver la surface exposée à l’eau savonneuse. Enlever les vêtements contaminés. Si une

irritation ou une rougeur se développe, consulter un médecin.

Contact avec les yeux…………………………….. Vérifier et enlever les lentilles de contact. Rincer immédiatement les yeux avec de l’eau

pendant au moins 15 minutes, garder les paupières ouvertes. Consulter un médecin en

cas de toute irritation.

Ingestion……………………………………………….. Ingestion n’est pas une voie probable de l’exposition. En cas d’ingestion, ne pas faire

vomir, consulter un médecin.

Symptômes/effets plus importants, aigus et . Une attention médicale immédiate est nécessaire.

retardés

Indication des soins médicaux immédiats et Fournir des mesures générales de soutien et le traiter selon les symptômes. Donner de

traitement spécial nécessaire l’oxygène en cas d’essoufflement. Réchauffer la victime. Garder la victime sous

observation. Les symptômes peuvent être retardés.

SECTION 05: MESURES DE LUTTE CONTRE L’INCENDIE

D’extinction approprié……………………………… Poudre chimique sèche. Dioxyde de carbone. Mousse, eau pulvérisée ou en brouillard.

D’extinction inappropriés…………………………. Ne pas utiliser de jet d’eau comme un extincteur, comme cela se propagera le feu.

Dangers particuliers découlant de la ………… Contenu sous pression. Contenants sous pression pouvant exploser lorsqu’ils sont

substance chimique exposés à la chaleur ou de flamme.

Équipement spécial de protection et ………… Pompiers doivent utiliser un équipement de protection standard y compris manteau

précautions pour les pompiers ignifuge, casque avec l’eau pour éviter l’accumulation de pression de vapeur vers le haut.

Pour énorme incendie dans le compartiment, utiliser le support à boyau sans pilote ou

moniteur buses, si possible. Si ce n’est pas le cas, retirer et laisser le feu brûler.

SECTION 06: MESURES À PRENDRE EN CAS DE DISPERSION ACCIDENTELLE

Précautions individuelles, équipements de .. Aucun prend les mesures impliquant des risques personnels ou sans formation adéquate.

protection et procédures d’urgence Évacuer les régions avoisinantes. Empêchent le personnel inutile et non protégé de

pénétrer. Évitez de marcher à travers le produit déversé. Éviter de respirer les vapeurs ou

brouillards. Prévoyez une ventilation adéquate. Porter un respirateur approprié lorsque la

ventilation est inadéquate. Mettre sur les équipements de protection individuelle approprié

(voir Section 08).

Méthodes et matériaux de confinement et de Zones de déversement peuvent être glissants. Faire attention à éviter les chutes ou autres

nettoyage accidents . Contenir le déversement. Nettoyer la zone de déversement à l’eau et de

détergent. Une fois que le produit déversé a été recueilli, utiliser chiffons ou autre matériau

approprié pour déversement propre zone. Chiffons doivent être correctement éliminés.

Précautions environnementales……………….. Garder hors de drains, égouts, fossés et cours d’eau. Minimisez l’utilisation de l’eau pour

éviter la contamination de l’environnement.

SECTION 07: PRÉCAUTIONS DE STOCKAGE, DE L’EMPLOI ET DE MANIPULATION

Précautions pour la manipulation……………… Récipient sous pression : ne pas percer ou brûler, même après utilisation. Ne pas utiliser si

le bouton du spray est manquant ou défectueux. Ne pas vaporiser sur une flamme nue ou

tout autre matériau incandescent. Ne pas pressuriser, couper, souder, braser, souder,

percer, moudre ou exposer des conteneurs vides pour la chaleur, d’étincelles ou de

flammes nues. Éviter tout contact avec les yeux, la peau et vêtements. Éviter de respirer

les vapeurs de ce produit. Éviter tout contact avec la peau et les yeux. Éviter une

exposition prolongée. Utiliser dans des endroits bien aérés.

Conditions d’entreposage sécuritaire, y ……. Magasin fermé à clé. Récipient sous pression. Protéger des rayons du soleil et ne pas

compris les incompatibilités exposer à des températures supérieures à 50° C (122° F). Ne pas percer, incinérer ou

écraser. Ne pas manipuler ou entreposer près d’une flamme, de chaleur ou d’autres

sources d’ignition. Magasin loin des matières incompatibles (voir Section 10).

SECTION 08: MESURES DE PROTECTION CONTRE L`EXPOSITION / PROTECTION INDIVIDUELLE

ACGIH TLV OSHA PEL NIOSH

INGRÉDIENTS TWA STEL PEL STEL REL

Naphta (pétrole), traités 353 ppm Non Disponible Non Disponible Non Disponible Non Disponible

hydro lumière

Isobutane 800 ppm 100 ppm 800 ppm Non disponible 800 ppm

Essence mineral inodore Non disponsible Non disponsible Non disponsible Non disponsible Non disponsible

Propane 2,500 ppm Non disponible 1,000 ppm Non disponible 1,000 ppm

Alcool Isopropyle 200 ppm 400 ppm 400 ppm (980 500 ppm (1225 400 ppm (980

mg/m3) mg/m3) mg/m3)

Powered by www.trivalent.com

00000711 FICHES DE DONNÉES DE SÉCURITÉ Page 3

PRODUIT: Lubco Motorbike Insect & Tar Remover – 200 g CODE: A6-000601-USA

SECTION 08: MESURES DE PROTECTION CONTRE L`EXPOSITION / PROTECTION INDIVIDUELLE

ACGIH TLV OSHA PEL NIOSH

INGRÉDIENTS TWA STEL PEL STEL REL

2-Butoxyéthanol 20 ppm Non disponible Non disponible Non disponible 50 ppm

Distillats de pétrole 200 mg/m3 Non disponsible 5 mg/m3 Non disponsible Non disponsible

Agents tensio-actifs Non disponible Non disponible Non disponible Non disponible Non disponible

Contrôles d’ingénierie appropriés……………… L’évacuation par une ventilation locale est nécessaire pour maintenir le point d’utilisation

ci-dessous sous la Valeur du Seuil de Limite si le personnel n’est pas protégé.

Mesures de Protection individuelle :

Protection des yeux/visage……………………… Ne recevez pas dans les yeux. Porter des lunettes de sécurité avec écrans latéraux.

Protection de la peau……………………………… Des gants jetables sont recommandés. Éviter tout contact avec la peau. Porter des

vêtements appropriés résistants aux produits chimiques.

Protection des voies respiratoires…………….. Respirateur de poussière et de la brume d’utilisation.

Risques thermiques………………………………… Aucune n’est connue.

Considérations d’hygiène générale…………… Lors de l’utilisation, pas manger, boire ou fumer. Respectez toujours les mesures d’hygiène

personnelle, tels que lavage après avoir manipulé le matériel et avant de manger, boire ou

fumer. Régulièrement laver les vêtements de travail et équipements de protection avant

d’utiliser.

SECTION 09: PROPRIÉTÉS PHYSICO-CHIMIQUES

Formulaire…………………………………………….. Aérosol.

Apparence physique……………………………….. Blanc.

Odeur…………………………………………………… N/A.

Seuil de l’odeur (ppm)…………………………….. N/A.

Gravité spécifique (aérosol)…………………….. 0,836.

Densité (liquide)…………………………………….. 0.905.

Pression de vapeur des aérosols (lb/po2, 21° 40-50.

C)

Densité de vapeur (Air = 1)……………………… > 1.

pH………………………………………………………… 8.81.

Liquide de Point d’ébullition (° C)………………. -11.72 ° C (10,9 ° F). (Pour le gaz propulseur).

Point de fusion/congélation (° C)………………. N/A.

Point d’éclair (° C), méthode…………………….. Coupe fermée :-83.15 ° c (-117.7 ° f). (Pour le gaz propulseur).

Retour de flamme…………………………………… Non.

Taux d’évaporation (acétate de n-butyle = 1) Non disponible.

Teneur en COV……………………………………… N/A.

Solubilité dans l’eau………………………………… N/A.

Projection de flamme aérosol…………………… Aucune donnée.

Température d’auto-inflammation (° C)……… 460° C (860° F). (propergol).

Limite inférieur d’inflammabilité (% vol.)…….. 1.8. (propergol).

Limite supérieure d’inflammabilité (% vol.)…. 9.5. (propergol).

Coefficient de répartition eau/huile……………. N/A.

Viscosité……………………………………………….. N/A.

SECTION 10: STABILITÉ DU PRODUIT ET RÉACTIVITÉ

Réactivité ……………………………………………… Produit non réactif dans des conditions normales d’utilisation.

Stabilité chimique…………………………………… Matériau est stable dans des conditions normales.

Possibilité de réactions dangereuses………… Ne se produit pas.

Conditions à éviter………………………………….. Évitez les sources de chaleur et la flamme et la charge électrostatique. Entrer en contact

avec des substances incompatibles.

Matières incompatibles……………………………. Agents oxydants forts. Acides forts. Bases fortes.

Produits de décomposition dangereux ……… Monoxyde de carbone, le dioxyde de carbone, le phosgène, gaz de chlorure d’hydrogène.

Products

SECTION 11: INFORMATION TOXICOLOGIQUE

INGRÉDIENTS LC50 LD50

Naphta (pétrole), traités hydro lumière >20 mg/L (Rat,4hrs) >5000 mg/kg (Oral,Rat); >3000

mg/kg (Skin,Rabbit)

Isobutane 658 mg/L (4hrs,Rat) Non disponible

Essence mineral inodore >5900 mg/m3 (rat-4hrs) >8000 ml/kg (rat -oral)

Propane >800,000 ppm (15 min – rat) Non disponible

Powered by www.trivalent.com

00000711 FICHES DE DONNÉES DE SÉCURITÉ Page 4

PRODUIT: Lubco Motorbike Insect & Tar Remover – 200 g CODE: A6-000601-USA

SECTION 11: INFORMATION TOXICOLOGIQUE

INGRÉDIENTS LC50 LD50

Alcool Isopropyle 51.045 mg/L 8h rat 5500 mg/kg Rat orale;12870

mg/kg Lapin cutanee

2-Butoxyéthanol 450 ppm (4 hrs – rabbit) 470 mg/kg (rat)

Distillats de pétrole >5 mg/l (4hrs – rat) >5,000 mg/kg (rat – Oral); >2,000

mg/kg (rabbit – Dermal)

Agents tensio-actifs Non disponible Non disponible

Informations sur les Routes probables

d’exposition :

Voies de pénétration – Inhalation………………. Oui.

Voies de pénétration – Skin & yeux…………… Oui.

Voies de pénétration – Ingestion……………….. Non.

Voies de pénétration – Absorption par la peau Non.

Symptômes liés aux caractéristiques

physiques, chimiques et toxicologiques

Toxicité aiguë………………………………………… Pas d’effets significatifs connus.

Corrosion/Irritation cutanée……………………… Provoque une irritation cutanée bénigne. Le contact prolongé peut être plus irritant.

Irritation oculaire/dommages oculaires graves Peut irriter les yeux.

Sensibilisation respiratoire ou cutanée………. L’inhalation peut provoquer une irritation des voies respiratoires.

Mutagénicité sur les cellules germinales……. Aucune donnée disponible pour indiquer les produits ou les composants présents à plus de

0,1 % sont mutagènes.

Cancérogénicité…………………………………….. Aucune information n’est disponible.

Toxicité pour la reproduction……………………. Selon les données disponibles, les critères de classification ne sont pas remplies.

STOT – exposition unique………………………… Organes cibles toxicité unique exposition catégorie 3. Peut provoquer somnolence et

vertiges.

STOT – exposition répétée………………………. Pas d’effets significatifs connus.

Danger par aspiration

Effets chroniques……………………………………. Exposition répétée ou prolongée de la peau peut entraîner une irritation modérée,

séchage, fissuration et dessèchements de la peau (dermatite).

SECTION 12: RENSEIGNEMENTS ÉCOTOXICOLOGIQUES

Écotoxicité…………………………………………….. Peut être dangereux pour l’environnement. Il n’existe aucune donnée sur le produit

lui-même. Ne devraient pas être rejetées dans l’environnement. Naphta de pétrole (CAS #:

64742-49-0): toxicité pour les poissons : CL50 1,0 mg/L, 48 heures ; Toxicité pour les

autres invertébrés aquatiques : L50 3,87 mg/L, 48 heures ; Toxicité pour les algues : EC50

55 mg/L, en 48 h. 2-butoxyéthanol (CAS n°: 111-76-2): non établi. Isopropanol (no CAS :

67-63-0) : toxicité pour les poissons : CL50 9 640 mg/L, 96 heures ; Toxicité pour les

autres invertébrés aquatiques : 5 102 mg/L, 96 heures ; Toxicité pour les algues : LE50

&gt; 2 000 mg/L, 72 hrs.

Persistance et dégradabilité ……………………. Le produit lui-même n’a pas été testé.

Potentiel de bioaccumulation…………………… Le produit lui-même n’a pas été testé.

Mobilité dans le sol…………………………………. Le produit lui-même n’a pas été testé.

Autres effets nocifs…………………………………. Aucune n’est connue.

SECTION 13: INFORMATIONS SUR L’ÉLIMINATION DES DÉCHETS

Méthodes d’élimination appropriées………….. Ce produit et son récipient doivent être éliminés comme déchet dangereux. Éviter le rejet

dans l’environnement. Les rinçages et de l’eau déversées sont classés comme déchets

chimiques et doivent être éliminés conformément aux règlements les, provinces et

fédéraux. Contenu sous pression. Ne pas percer, incinérer ou exposer à la chaleur, même

lorsqu’il est vide.

SECTION 14: INFORMATION RELATIVES AU TRANSPORT

TMD (Canada – Road)…………………………….. AÉROSOLS, classe 2.1, UN1950.

DOT (U.S. route)……………………………………. AÉROSOLS, classe 2.1, UN1950, LTD QTY, bien de consommation ORM-D.

IMDG (International – Marine)…………………… AÉROSOLS, classe 2.1, UN1950.

IATA (International Air)……………………………. AÉROSOLS, classe 2.1, UN1950, LTD QTY.

SECTION 15: INFORMATION RÉGLEMENTAIRES

Règlements de Canada :…………………………. Classification du SIMDUT. A: gaz comprimé. D2B : Matières causant d’autres matériaux

toxiques.

Loi sur la Protection de l’environnement …… Tous les ingrédients figurent sur la liste intérieure des Substances (LIS).

canadien (LCPE)

Powered by www.trivalent.com

00000711 FICHES DE DONNÉES DE SÉCURITÉ Page 5

PRODUIT: Lubco Motorbike Insect & Tar Remover – 200 g CODE: A6-000601-USA

SECTION 15: INFORMATION RÉGLEMENTAIRES

Règlements américains…………………………… Loi sur la Protection environnementale : Les constituants de ce produit figurent sur

l’inventaire du TSCA. Ce produit est considéré comme dangereux par l’OSHA Hazard

Communication Standard.

SECTION 16: AUTRES RENSEIGNEMENTS

Clause de non-responsabilité…………………… Les informations contenues dans ce document sont issues des données considérées

comme exactes. Aucune garantie ou garantie expresse ou implicite quant à l’exactitude de

ces données ou les résultats obtenus par l’utilisation de celui-ci. Le fournisseur de SDS

n’assume aucune responsabilité pour les dommages corporels ou matériels personnels à

des fournisseurs ou des utilisateurs ou des tiers, causés par le matériel. Ces fournisseurs

ou utilisateurs assumeront tous les risques avec l’utilisation du matériel. Ce produit a été

classé selon les critères de danger du RPC et de la FDS contient tous les renseignements

exigés par le RPC. .

Abréviations…………………………………………… ACGIH : American Conference of Governmental Industrial Hygienists ; CAS: Chemical

Abstract Service ; NIOSH : National Institute for Occupational Safety and Health, OSHA :

Occupational Safety and Health Administration – États-Unis ; TSCA : Toxic Substances

contrôlent Act 1976-USA ; PEL : Limite d’exposition permise ; REL : Recommandé limite

d’exposition ; VLE : Valeur limite ; COV : Teneur organique Volatile ; SIMDUT : Système

d’Information au travail matières dangereuses STOT : toxicité pour certains organes cibles.

Préparé par ………………………………………….. Affairs Regulatory

Version Révisée ……………………………………. JAN 27/2017